Sn-3.7wt.%Ag-0.9wt.%Zn alloy was directionally solidified upward under different conditions, with different growth rates (V = 3.38 220.12 μm/s) at a constant temperature gradient (G = 4.33 K/mm) and with different temperature gradients (G = 4.33 -12.41 K/mm) at a constant growth rate (V = 11.52 μm/s) by using a Bridgman-type directional solidification furnace. The microstructure was observed to...

The propagation of solidified zones in the course of subaqueous liquefied sediment flow is theoretically discussed. The coupled systems of Navier-Stokes equations and consolidation equation are numerically solved under moving boundary conditions, with consideration of the concurrent evolutions of the flow surface as well as of the internally formed interface between the fluid and solidified zon...

Rapid solidification by planar flow casting has been found to have introduced deficiencies, viz. partial crystallinity, air pockets and compositional difference in the ribbons of rapidly solidified Ti42⋅9Cu57⋅1 alloy. In order to investigate the effects of these deficiencies on the corrosion of rapidly solidified Ti42⋅9Cu57⋅1 alloy ribbons, electrochemical behaviour of alloy ribbons has been in...

Agrobacterium tumefaciens C58 grown on acidic medium containing glucose and solidified with bacteriological agar expressed a virB::lacZ fusion. No expression of this fusion was observed on a similar medium which was solidified with purified agarose. The fraction from bacteriological agar which was responsible for vir gene induction was extracted with methanol and partially purified by preparati...

this research concentrates on the effects of low frequency, vertical mechanical vibration during solidification on the microstructure and mechanical properties of a380 aluminum alloy. two series of sr-modified and al-5ti-b grain refined a380 alloy samples were solidified in both static and dynamic conditions in the frequency and amplitude of 60 hz and 0.2 m, respectively. their physical, micro-...

During casting of aluminum alloys, the partially solidified material is submitted to thermally induced strains that can lead to severe casting defects, such as hot tearing. In this work, carried out in the frame of the European project VIR[CAST], the rheological behavior of a partially solidified AA5182 aluminum alloy has been investigated in order to provide constitutive equations to predict h...

Magnetic and structural aspects of the annealing-induced transformation of rapidly-solidified Mn55Al45 ribbons from the as-quenched metastable antiferromagnetic (AF) ε-phase to the target ferromagnetic (FM) L10 τ-phase are investigated. The as-solidified material exhibits a majority hexagonal ε-MnAl phase revealing a large exchange bias shift below a magnetic blocking temperature TB~95 K (Hex~1...

The Ni83.25Zr16.75 peritectic alloy was undercooled by electromagnetic levitation method up to 198 K. The measured dendritic growth velocity shows a steep acceleration at a critical undercooling of ΔTcrit = 124 K, which provides an evidence of the transition of the primary growth mode from Ni7Zr2 phase to peritectic phase Ni5Zr. This is ascertained by combining the temperature-time profile and ...

Linum usitatissimum protoplast-derived colonies that are cultured in auxin-supplemented medium and immobilized in Ca(2+)-alginate matrix form round colonies that develop into polarized, embryo-like structures. On the other hand, protoplast-derived colonies that are immobilized in agarose do not show an organized morphogenetic response, and unique, ionically bound cell-wall protein patterns matc...

The objective of our work was to study the micromeritic properties of lyophilized diclofenac potassium-loaded lipospheres and to evaluate in vivo, the analgesic properties of diclofenac potassium in the lipospheres in addition to other in vitro properties. Solidified reverse micellar solutions were prepared by fusion using 1:1, 2:1, and 1:2% w/w of Phospholipon(®) 90H and Softisan(®) 154. Diclo...