نتایج جستجو برای: increase heat transfer

تعداد نتایج: 1230433  

پایان نامه :وزارت علوم، تحقیقات و فناوری - دانشگاه صنعتی اصفهان 1389

run-out-table (rot) is located between last finishing stand and down coiler in a hot strip mill. as the hot steel strip passes from rot, water jets impact on it from top and bottom and strip temperature decreases approximately from 800-950 °c to 500-750°c. the temperature history that strip experience while passing through rot affects significantly the metallurgical and mechanical properties, s...

Journal: :international journal of nano dimension 0
m. falahaty naghibi school of mechanical enginnering, shahid rajaee teacher training university, tehran, iran. m. rahimi-esbo young researchers and elite club, buin zahra branch, islamic azad university, buin zahra, iran. r. mohammadyari young researchers and elite club, buin zahra branch, islamic azad university, buin zahra, iran. k. mobini school of mechanical enginnering, shahid rajaee teacher training university, tehran, iran.

using of nanofluids and ducts with corrugated walls are both supposed to enhance heat transfer, by increasing the heat transfer fluid conductivity and the heat transfer area respectively. use of a diverging duct with a jet at inlet section may further increase heat transfer by creating recirculation zones inside the duct. in this work two-dimensional incompressible laminar flow of a nanofluid e...

Heat Transfer has special importance in engineering applications. So, researchers have suggested different new idea to increase heat transfer and using nanofluid is one of these methods In recent years, new methods have been used. One of these methods is the use of nanofluids, ., because nanofluids have higher heat transfer potential than base conventional fluids. In this investigation effect o...

Journal: :فصلنامه علمی پژوهشی مهندسی مکانیک جامدات واحد خمینی شهر 0
mousa heydari msc, department of mechanical engineering, khomeinishahr branch, islamic azad university, khomeinishahr, iran davood toghraie assistant professor, department of mechanical engineering, khomeinishahr branch, islamic azad university, isfahan omid ali akbari msc, department of mechanical engineering, khomeinishahr branch, islamic azad university, khomeinishahr, iran

in this numerical study the the heat transfer and laminar nanofluid flow in the three-dimensional microchannels with triangular cross-section is simulated. for increase the heat transfer from the walls of the channel, semiattached & offset mid- truncated rib,s placed in the canal, and the tooth geometry and the impact is studied. in this study, the water is base fluid, and the influence of the ...

Journal: :international journal of nano dimension 0
r. aghayari young researchers and elite club, shahrood branch, islamic azad university, shahrood, iran h. maddah department of chemistry, sciences faculty, arak branch, islamic azad university, arak, iran j. baghbani arani department of chemical engineering, faculty of engineering, arak university, arak, iran h. mohammadiun assistant professor, department of mechanical engineering, shahrood branch, islamic azad university, shahrood, iran e. nikpanje department of chemistry, sciences faculty, north tehran branch, islamic azad university, north tehran, iran.

one way to increase the heat transfer is to use perforated twisted tapes with different hole diameters, which largely improve heat transfer with an increase in the heat transfer area at the constant volume and more mixed flow. in the previous studies, the effect of nanofluids with perforated twisted tapes is less studied. in this work, the performance of water / iron oxide nanofluid in a double...

Cross-corrugated triangular channels increase heat transfer in heat exchangers. The mixing effect increases the heat transfer coefficient at the surfaces. In this study, the fluid flow and heat transfer in a triangular corrugated channel are modeled under two constant heat fluxes and different Reynolds numbers. In order to validate, k-ω turbulence model is used. Also, the effect of magnetic fie...

Using of nanofluids and ducts with corrugated walls are both supposed to enhance heat transfer, by increasing the heat transfer fluid conductivity and the heat transfer area respectively. Use of a diverging duct with a jet at inlet section may further increase heat transfer by creating recirculation zones inside the duct. In this work two-dimensional incompressible laminar flow of a nanofluid e...

Using of nanofluids and ducts with corrugated walls are both supposed to enhance heat transfer, by increasing the heat transfer fluid conductivity and the heat transfer area respectively. Use of a diverging duct with a jet at inlet section may further increase heat transfer by creating recirculation zones inside the duct. In this work two-dimensional incompressible laminar flow of a nanofluid e...

Journal: :transport phenomena in nano and micro scales 2015
r. aghayari h. maddah z. sharifnezhad a. hakiminejad s. sarli

nanofluid is a new class of heat transfer fluids engineered by dispersing metallic or non-metallic nanoparticles with a typical size of less than 100 nm in the conventional heat transfer fluids.this article aims to investigate the overall and convection heat transfer coefficient and nusselt number of al2o3-water nanofluid flowing in a horizontal double pipe heat exchanger under turbulent flow (...

Journal: :transport phenomena in nano and micro scales 2015
h. aberoumand a. jahani s. aberoumand a. jafarimoghaddam

in order to examine the laminar convective heat transfer of nanofluid, experiments carried out using silver-oil nanofluid in a concentric annulus with outer constant heat flux as boundary condition. silver-oil nanofluid prepared by electrical explosion of wire technique and observed no nanoparticles agglomeration during nanofluid preparation process and carried out experiments. the average size...

نمودار تعداد نتایج جستجو در هر سال

با کلیک روی نمودار نتایج را به سال انتشار فیلتر کنید