To evaluate the effect of a dentin adhesive on sclerotic dentin, contraction gap width and shear bond strength were measured. Dentin cavity wall was pretreated with an experimental dentin bonding system with and without a dentin primer, or with a commercial dentin bonding system. In the experimental dentin bonding groups, contraction gap width of sclerotic dentin was significantly smaller than ...

The aim of this study was to evaluate the microtensile bond strength (microTBS) and the elemental contents of the adhesive interface created to normal versus caries-affected dentin. Extracted human molars with coronal carious lesions were used in this study. A self-etching primer/adhesive system (Clearfil Protect Bond) was applied to flat dentin surfaces with normal and caries-affected dentin a...

The relation between the bonding efficacy of the dentin adhesive and the physical change of the dentin after treatment with various dentin cleansers was investigated. The dentin surface was cleaned with one of the seven experimental dentin cleansers, 5, 10, 20, 30 and 40% of the phosphoric acid, neutralized 0.5 M EDTA solution (pH 7.4) and 9.1% pyruvic acid containing 9.1% glycine, prior to the...

This study evaluated the effect of dentin surface treatment on shear bond strengths of two light- cured glass ionomer restorative materials to dentin. Cylinders of Fuji II LC and VariGlass VLC were bonded to dentin surfaces that were untreated, treated with a 10% polyacrylic acid (GC Conditioner), or treated with a dentin bonding agent primer (Prisma Universal Bond 3 Primer). Specimens were the...

This study determined the shear bond strength of resin composites to primary dentin using three dentin adhesives and the presence or absence of a hybrid zone. The buccal and lingual surfaces of 40 recently extracted noncarious primary teeth were ground flat with SiC paper ending with the 600 grit. The teeth were divided at randomly into eight groups of five teeth (10 surfaces) each: 1) Unetched...

The relatlon between the bonding eMcacy ef the dentin adhesive and the physical change of the dentin after treatment with various dentin cleansers was investigated, The dentin surface was cleaned with one of the seven experimental dentin cleansers, 5, 10, 20, 30 and 40% of the phosphoric acid, neutralized O,5M EDTA solution (pH7.4) and 9.1% pyruvic acid containing 9,1% glycin, prior to the comb...

INTRODUCTION ADHESIVE DENTISTRY • Indications for Use of Adhesives • Advantages of Bonding Techniques • Mechanism of Adhesion • Factors Affecting Adhesion ENAMEL BONDING • Steps for Enamel Bonding • Mechanism of Etching DENTIN BONDING • Conditioning of Dentin • Priming of Dentin • Moist vs Dry Dentin DENTIN BONDING AGENT • Mechanism of Bonding • Evolution of Dentin Bonding Agents • Nanofilled B...

The mechanical properties of enamel and dentin were studied using test specimens having the same shape and dimensions because these properties might vary with the experimental conditions and specimen shapes and dimensions. Healthy human teeth were used as specimens for mechanical tests. The stress (MPa), strain (%), and elastic modulus (E, MPa) of the specimens were obtained from compression te...

The purpose of this study was to test the hypothesis that both human and bovine sclerotic dentin have similar hardness properties, in addition to similar micromorphological characteristics. Sixteen teeth (8 human and 8 bovine) exhibiting exposed dentin in the incisal edge and showing characteristics typical of sclerosis were used. Vickers surface microhardness testing was conducted. Three areas...

PURPOSE This study compared the dentin collagen cross-linking potential of carbodiimide (EDC) prepared in three most commonly used solvents in dental adhesive systems: water, ethanol, and acetone. MATERIALS AND METHODS Thirty-eight extracted caries-free human permanent molars were used in this study. Demineralized dentin beams were prepared and cross linked by 0.3 M EDC in water, acetone, or ...