نتایج جستجو برای: 6061 al alloy

تعداد نتایج: 488074  

2002

The material flow and microstructural evolution in the friction stir welds of a 6061-Al alloy to itself and of a 6061-Al alloy to 2024-Al alloy plates of 12.7 mm in thickness were studied under different welding conditions. The results showed that plastic deformation, flow, and mechanical mixing of the material exhibit distinct asymmetry characteristics at both sides of the same and dissimilar ...

Eslami, A., Karimzadeh, F., Zohoori-Shoar, V. ,

In this study, The Al 6061 alloy sheets were produced by Cryorolling process and then were welded by resistance spot welding method. In this regard, the solution treated Al 6061 alloy cryorolled subsequently up to 90% reduction in thickness to produce nanostructure alloy. The cryorolled sheets were then subjected to aging treatment (130˚C-30h) in order to obtain simultaneous strength and ductil...

Eslami, A., Karimzadeh, F., Zohoori-Shoar, V. ,

In this study, The Al 6061 alloy sheets were produced by Cryorolling process and then were welded by resistance spot welding method. In this regard, the solution treated Al 6061 alloy cryorolled subsequently up to 90% reduction in thickness to produce nanostructure alloy. The cryorolled sheets were then subjected to aging treatment (130˚C-30h) in order to obtain simultaneous strength and ductil...

2011
Mohammed A. Amin

The electrochemical and corrosion behaviour of Al-6061, Al-4.5%Cu and Al-7.5%Cu alloys were studied in 0.50 M KSCN solution at 25 C. Open-circuit potential, Tafel polarization and ICP-AES measurements were used to study the uniform corrosion process on the surfaces of the tested alloys. Cyclic polarization measurements were employed for pitting corrosion studies. Obtained results were compared ...

2012
A. Anandha Moorthy N. Natarajan R. Sivakumar M. Manojkumar M. Suresh

The experimental investigation of hybrid metal matrix composites with fly ash and graphite reinforced aluminium alloy (Al 6061) composites samples, processed by stir casting route are reported. The aluminium alloy was reinforced with 3 wt.%, 6 wt.%, 9 wt.% fly ash and fixed 3 wt.% of graphite to mixture the hybrid composite. Hardness of the hybrid composite were tested it was found that when th...

2004
W H Jiang

The present work demonstrates that friction stir welding (FSW) is a feasible route for joining 6061 aluminium (Al) alloy to AISI 1018 steel. The weld has a good weld quality and is free of cracks and porosity. The tensile failure happened at the boundary between the nugget and thermomechanically affected zone of the base Al alloy, indicating that the weld has a higher joining strength. Despite ...

2015
Maxim Murashkin Vladimir Terentiev Ruslan Valiev

The paper presents the evaluation of the mechanical and fatigue properties of an ultrafine-grained (UFG) Al 6061 alloy processed by high-pressure torsion (HPT) at room temperature (RT). A comparison is made between the UFG state and the coarse-grained (CG) one subjected to the conventional aging treatment Т6. It is shown that HPT processing leads to the formation of the UFG microstructure with ...

2016
Yufeng Sun Nobuhiro Tsuji Hidetoshi Fujii Giuseppe Casalino

The ultrafine grained (UFGed) 1050 Al plates with a thickness of 2 mm, which were produced by the accumulative roll bonding technique after five cycles, were friction stir butt welded to 2 mm thick 6061-T6 Al alloy plates at a different revolutionary pitch that varied from 0.5 to 1.25 mm/rev. In the stir zone, the initial nano-sized lamellar structure of the UFGed 1050 Al alloy plate transforme...

2016
Xuezheng Zhang Tijun Chen He Qin Chong Wang

Microstructural and mechanical characterization of 10 vol% SiC particles (SiCp) reinforced 6061 Al-based composite fabricated by powder thixoforming (PTF) was investigated in comparison with the PTF and permanent mold cast (PMC) 6061 monolithic alloys. The results reveal that the microstructure of the PMC alloy consists of coarse and equiaxed α dendrites and interdendritic net-like eutectic pha...

2015
H. C. Ananda Murthy

Aluminum matrix composites (AMCs), reinforced with ceramic particulates, have significant applications in the field of aerospace, marine, automobiles, sports and recreation. Al-TiC particulate composite has better potential for high-temperature applications. The corrosion behaviour of Al 6061-TiC particulate composites prepared by stir casting route, has been explored in chloride medium using e...

نمودار تعداد نتایج جستجو در هر سال

با کلیک روی نمودار نتایج را به سال انتشار فیلتر کنید