نتایج جستجو برای: mud pressure

تعداد نتایج: 414009  

Journal: :iranian journal of oil & gas science and technology 2012
mostafa sedaghatzadeh abbasali khodadadi mohammad reza tahmasebi birgani

designing drilling fluids for drilling in deep gas reservoirs and geothermal wells is a majorchallenge. cooling drilling fluids and preparing stable mud with high thermal conductivity are ofgreat concern. drilling nanofluids, i.e. a low fraction of carbon nanotube (cnt) well dispersed inmud, may enhance the mixture thermal conductivity compared to the base fluids. thus, they arepotentially usef...

2012
S. Archer V. Rasouli

In drilling operation the design of a proper mud weight to avoid any instability’s is important. A low mud weight may cause breakouts around the borehole whereas a high mud weight can fracture the formation. Mud weight design is based on two main factors: the mechanical properties of formations being drilled and the state of in-situ stresses in the field. While drilling in soft formations are t...

2013
Lyès Benamsili Gérald Hamon Jean-Pierre Korb

We propose a method that allows probing quantitatively the individual saturations of crudeoil/brine/mud-filtrate mixtures during imbibition-drainage experiments on a petroleum rock-system. The experiments have been also performed at different temperature and pressure conditions.

Journal: :Buildings 2021

To maximize the utilization of red mud in geopolymers, a mud–metakaolin (RM-MK) geopolymer and mud–fly ash (RM-FA) were prepared, respectively. The effects content on compressive strength microstructure geopolymers investigated under three different curing conditions. results showed that decreased linearly with an increase content, whether at room temperature or 80 °C. Surprisingly, autoclave, ...

2005
Rogério Martins Tavares José Ricardo Pelaquim Mendes Celso Kazuyuki Morooka João Carlos Ribeiro Plácido

During the petroleum well drilling operation many mechanical and hydraulic parameters are observed by an instrumentation system installed in the rig named mud-logging system. The mud-logging system is composed by several sensors distributed in the rig; these sensors measure different operation parameters like: hook load, column rotation, mud pit level, pumping pressure, etc. The mudlogging syst...

2017
Nicolas Gratiot Antoine Gardel Edward Anthony Edward J. Anthony

The South American coast between Brazil and Venezuela is affected by longshore migrating mud banks derived from the fine-grained Amazon sediment discharge. Onshore mud migration prevails over shallow ‘bank’ areas alternating alongshore with deeper ‘inter-bank’ areas. The transport on the inner shelf, and attachment to the shoreline, of this migrating mud has been attributed mainly to wind waves...

Journal: :Energy Science & Engineering 2022

Abstract Horizontal wells with a slim hole (HW‐SH), characterized by high productivity, environmental protection, and low cost are gradually being introduced into oil gas extraction processes in high‐temperature high‐pressure formations. However, the HW‐SH annulus is narrow, distributions of temperature pressure wellbore very different from those conventional horizontal wells. Furthermore, mud ...

In this paper, we detail our results for the impact of MWCNT on the thermal and rheological properties of oil-based drilling muds. Our analysis considers the effects of time, temperature, and MWCNT volume fraction. The scanning electron microscopy imaging technique was used to monitor the MWCNTsdispersion quality. The experimental results unveil a considerable enhancement in the thermal conduct...

Journal: :international journal of nanoscience and nanotechnology 2012
m. fereydouni s. sabbaghi r. saboori s. zeinali

polyanionic cellulose polymer is used as an additive in drilling mud in order to decrease water loss and mudcake- thickness. in this study effect of bulk and nanosize polyanionic cellulose on water loss and mud-cakethickness in mud drilling is investigated. polyanionic cellulose nanoparticles are made by using of ball milling. size of nanoparticles is measured by particle size analyzer. polyani...

2004
H. Lee

A laboratory-based experimental study was conducted to more completely understand the fundamentals of pressure transients produced by Formation Testing While Drilling (FTWD) equipment. These tools can be run in open hole, positioned at a desired level, and actuated to measure reservoir pressure and flow capacity while in a dynamic drilling environment. Any number of pressure measurements can be...

نمودار تعداد نتایج جستجو در هر سال

با کلیک روی نمودار نتایج را به سال انتشار فیلتر کنید