A. Amadeh
School of Metallurgy and Materials Engineering, Faculty of Engineering, University of Tehran, Tehran, Iran
[ 1 ] - Nickel-based Superalloy Layer Deposited on AISI H13 Hot Tool Steel Base Metal Using Explosion Cladding process
An experimental test was carried out to explosively clad solution annealed Inconel 718 superalloy on quench-tempered AISI H13 hot tool steel. A wavy with vortices interface geometry was obtained from this experiment. A gradual change in the wavelength along the direction of welding was observed which was due to a change in the impact angle, following the plate contacts. In this paper, the exper...
[ 2 ] - Wear behavior of carbon steel electrodeposited by nanocrystalline Ni–W coating
Ni-W coatings, compared to pure nanocrystalline Ni, exhibit higher hardness and wear resistance. In some cases, these coatings are considered as environmental friendly alternatives for hard chromium coating. Till now, most of Ni-W coatings have been produced by direct current electrodeposition from alkaline baths. In this study square pulse current was used for deposition of Ni-W precipitates f...
[ 3 ] - Effect of nano-structuration and compounding of YSZ APS TBCs with different thickness on coating performance in thermal shock conditions
Effect of nano-structuration and compounding of YSZ APS TBCs investigated on coating behavior in thermal shock conditions. The coatings were applied on Inconel 738 discs with three different thickness per powder. In order to harmonize the results from the samples, performance factor is defined as a criterion that in the starting of the activity has an amount of about 100 and is reduced after th...
[ 4 ] - Synthesis and Characterization of ZnO Nanostructures Grown via a Novel Atmospheric Pressure Solution Evaporation Method
In this study, a novel method called “atmospheric pressure solution evaporation (APSE)” wasdeveloped for growing of Zinc Oxide (ZnO) nanostructures on Al2O3 surface. Zinc acetate dihydrate,Polyvinyl Pyrrolidone, and deionized water were used as precursor, capping, and solvent, respectively.The growth of ZnO nanostructures from evaporated solution was performed at three temperatures of300, 400, ...
[ 5 ] - A STUDY ON THE ALUMINIZING OF ELECTRODEPOSITED NICKELAT 500 oC
Abstract: nanocrystalline nickel samples with the grain size of ~25 nm were prepared via direct current electrodeposition andaluminized for different durations by pack cementation method at 500 means of SEM, EDS and XRD techniques. According to results, short time aluminizing resulted in the formation of asingle aluminide layer whereas at long duration two distinct aluminide layers were formed....
[ 6 ] - مروری بر خواص، فرآوری تولید و کاربردهای مکس‌فازهای نانولایه‌ای
مکس فازها؛ نسلی جدید از مواد پیشرفته مهندسی و برخوردار از ترکیبی از خواص توامان فلزی و سرامیکی می‌باشند. این دسته از مواد با دارا بودن ساختاز ذاتی نانولایه‌ای, قابلیت بهره‌مندی از رفتار فلزات و آلیاژها نظیر انعطاف پذیری و چقرمگی مناسب، به همراه سودجستن از رفتار سرامیک‌ها همچون مقاومت سایشی و اکسایشی خوب را برخوردار می باشند. مجموعه خواص بسیار عالی، چگالی نسبتاً کم و قابلیت ماشین‌کاری بالا، این ت...
[ 7 ] - بررسی اثر نوع مواد اولیه در چگونگی و مکانیسم فرآوری تولید مکس فازهای پایه زیرکونیم نانوکریستالی
در این پژوهش تحقیقاتی؛ از روش آلیاژسازی مکانیکی به همراه تف جوشی پسین به‌منظور تولید و فرآوری مکس فازهای پایه زیرکونیم با ریزساختار نانوکریستالی بهره گرفته شده است. برای نیل به این مقصود؛ مقادیر مشخصی از ترکیبات عنصری با خلوص بالای اولیه با نسبت شیمیایی مشخص شامل هیدرید زیرکونیم، آلومینیم و گرافیت در دستگاه با انرژی بالای آسیاب مکانیکی سیاره‌ای برای مدت‌زمان‌های مشخص (5، 10، 20، 40 و 60 ساعت) ت...
نویسندگان همکار