Thermochemical Heat Storage Properties of Co3O4-X wt % Al2O3 and Co3O4-X wt % Y2O3 Composites (X=1, 2, 5, 8, 10)
نویسندگان
چکیده مقاله:
The effect of Al2O3 (1-10 wt %) and Y2O3 (1-10 wt %) additions on thermochemical heat storage properties of Co3O4/CoO system was investigated by thermogravimetry, XRD, and SEM analyses. Results showed that the addition of Al2O3 to Co3O4 at constant 8 h mechanical activation improved the redox cycle stability and increased oxygen sorption value and rate. It was found that oxygen sorption and their rate decreased with increasing the alumina content to more than 8 wt %. The formation of the spinel phase and an increase in its amount by increasing the alumina content led to a decrease in the oxygen sorption capacity. SEM studies showed that Al2O3 prevented the sintering and particle growth of cobalt oxide particles during reduction and re-oxidation processes. In addition, results showed that the addition of Y2O3 in all ranges to Co3O4 improved the redox cycle stability of cobalt oxide; however, it significantly decreased the oxygen sorption in the Co3O4/CoO system. XRD patterns of a sample containing 10 wt % yttria before the redox process indicated the presence of only Co3O4 phase; however, after three redox cycles, other phases including CoO and Y2O3 appeared.
منابع مشابه
Effects of Fe2O3 addition and mechanical activation on thermochemical heat storage properties of the Co3O4/CoO system
Effects of Fe2O3 addition (2-20 wt%) with 1 h mechanical activation on redox reactions of Co3O4 were studied by TG/DSC, SEM, and XRD analyses. The results showed that a Fe2O3 addition from 2 to 15 wt% increases the oxygen release from 1.4 to 3.4 wt% and decreases the reduction onset temperature from 1030 to 960 °C, while it increases the oxygen uptake value and re-oxidation onset temperature re...
متن کاملIsothermal Redox Kinetics of Co3O4-Fe2O3 Nano-Composite as a Thermochemical Heat Storage Material
Isothermal redox kinetics of as-received Co3O4 (AC), 1 h ball milled Co3O4 (BC), and 1 h ball milled Co3O4-15wt.% Fe2O3 (BCF) was investigated at various temperatures (1130, 1100, 1070, and 1040 °C for reduction and 830, 860, and 890°C for re-oxidation) by thermogravimetric method. It was found that mechanic...
متن کاملElectrical and photoresponse properties of Co3O4 nanowires
Related Articles A comparative study of ultraviolet photoconductivity relaxation in zinc oxide (ZnO) thin films deposited by different techniques J. Appl. Phys. 111, 102809 (2012) Effect of defect bands in β-In2S3 thin films J. Appl. Phys. 111, 093714 (2012) Photovoltaic properties of the p-CuO/n-Si heterojunction prepared through reactive magnetron sputtering J. Appl. Phys. 111, 084507 (2012) ...
متن کاملSensing Properties of Pd-Loaded Co3O4 Film for a ppb-Level NO Gas Sensor
We prepared 0.1 wt%-30 wt% Pd-loaded Co3O4 by a colloidal mixing method and investigated the sensing properties of a Pd-loaded Co3O4 sensor element, such as the sensor response, 90% response time, 90% recovery time, and signal-to-noise (S/N) ratio, toward low nitric oxide (NO) gas levels in the range from 50 to 200 parts per billion. The structural properties of the Pd-loaded Co3O4 powder were ...
متن کاملElectro Discharge Machining Of Aluminium Alloy (LM6)-5 wt.% SiCp Composites Using Copper Electrodes
Metal matrix composites (MMCs) are now gaining their usage in aerospace, automotive and biomedical industries because of their inherent properties like high strength to weight ratio, low wear rate etc. To machine these types of materials conventional machining methods are unsuitable because of high tool wear and tooling cost. Electro discharge Machining (EDM) is one of the important nontraditio...
متن کاملHydrogen Desorption Properties of Nanocrystalline MgH2-10 wt.% ZrB2 Composite Prepared by Mechanical Alloying
Storage of hydrogen is one of the key challenges in developing hydrogen economy. Magnesium hydride (MgH2) is an attractive candidate for solid-state hydrogen storage for on-board applications. In this study, 10 wt.% ZrB2 was co-milled with magnesium hydride at different milling times to produce nanocrystalline composite powder. The effect of milling time and additive on the hydrogen desorption...
متن کاملمنابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ذخیره در منابع من قبلا به منابع من ذحیره شده{@ msg_add @}
عنوان ژورنال
دوره 6 شماره 4
صفحات 27- 34
تاریخ انتشار 2019-10-01
با دنبال کردن یک ژورنال هنگامی که شماره جدید این ژورنال منتشر می شود به شما از طریق ایمیل اطلاع داده می شود.
کلمات کلیدی
میزبانی شده توسط پلتفرم ابری doprax.com
copyright © 2015-2023