Investigation of the Forming Force in Torsion Extrusion Process of Aluminum Alloy 1050
نویسندگان
چکیده مقاله:
In this paper, torsion extrusion (TE) process on 1050 aluminum alloy was investigated by simulation as a severe plastic deformation (SPD) method and the effects of friction coefficient, angular velocity of the rotating die and punch speed on maximum punch force were studied. A finite element (FE) model was developed to simulate the TE process via DEFORM software. The FE results were validated compared with experimental results and then the FE model was used for implementing the set of simulations designed by Taguchi’s L9 orthogonal array. Maximum punch force was determined and put into signal to noise (S/N) ratio and the analysis of variance (ANOVA) techniques to specify the importance and contribution of parameters. The results indicated that the friction coefficient has the most effect on maximum punch force and effects of the angular velocity and punch speed are not sensible. Results analysis represented that maximum punch force enhances by increasing the friction coefficient. Moreover, friction coefficient of 0.18, angular velocity of 0.11 rad/s and punch speed of 0.2 mm/s lead to the minimum punch force.
منابع مشابه
The Effects of Forming Parameters on the Single Point Incremental Forming of 1050 Aluminum Alloy Sheet
The single point incremental forming (SPIF) is one of the dieless forming processes which is widely used in the sheet metal forming. The correct selection of the SPIF parameters influences the formability and quality of the product. In the present study, the Gurson-Tvergaard Needleman (GTN) damage model was used for the fracture prediction in the numerical simulation of the SPIF process of alum...
متن کاملMicrostructural evolution during recrystallization in hot rolled Aluminum Alloy 1050
The evolution of texture as a function of recrystallization has been characterized for hot-rolled AA1050. Samples prepared from a hot rolled sheet were annealed isothermally for sufficient time to allow complete recrystallization. The spatial orientation variation within the deformed microstructure of nucleation, growth and orientations of recrystallized grains is examined. The microstructural ...
متن کاملInvestigation of Flat Clinching Process Combined with Material Forming Technology for Aluminum Alloy
In recent years, the use of aluminum alloy has tended to increase for building lightweight automobiles to reduce their automotive weight, which is helpful to save energy and protect the environment. In order to join aluminum alloy, a flat-clinching process combined with material forming technology was investigated to join aluminum alloy sheets using an experimental and a numerical method. Al106...
متن کاملthe investigation of research articles in applied linguistics: convergence and divergence in iranian elt context
چکیده ندارد.
An Analysis on the Forming Characteristics of commercial pure Aluminum AA 1100 in Radial-Forward Extrusion Process
Abstract: In this paper, the forming process of a central hub by radial-forward extrusion is analyzed by using the finite element software, ABAQUS. Radial-forward extrusion is used to produce hollow parts that generally feature a central hub with radial protrusions. Effective design factors such as mandrel diameter, die corner radius, die fillet radius, mandrel corner radius, tube wall thick...
متن کاملمنابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ذخیره در منابع من قبلا به منابع من ذحیره شده{@ msg_add @}
عنوان ژورنال
دوره 30 شماره 6
صفحات 920- 925
تاریخ انتشار 2017-06-01
با دنبال کردن یک ژورنال هنگامی که شماره جدید این ژورنال منتشر می شود به شما از طریق ایمیل اطلاع داده می شود.
میزبانی شده توسط پلتفرم ابری doprax.com
copyright © 2015-2023