Influence of shielding gas composition on weld structure in pulsed Nd: YAG laser welding
نویسندگان
چکیده مقاله:
This work studied the effect of additions of carbon dioxide to argon shielding gas on the weld shape and microstructure of ST14 steel in pulsed Nd: YAG laser welding. By additions of carbon dioxide up to 15%,the weld area and depth/width ratio decreases while rising of carbon dioxide up to 25% causes increasing of weld area and depth/width ratio. It is observed that the weld metal microstructure is mainly constructed from polygonal ferrite under 0 to 15% CO2 additions to argon, but both polygonal and acicular ferrites are observed as the CO2 level of Ar+ CO2 mixtures increases from 15 to 25%. The shape and microstructure of pulsed Nd: YAG laser welds is believed to be closely related to laser absorption coefficient, laser energy absorption on the work-piece surface and formation of oxide layer on the work-piece surface.
منابع مشابه
Influence of shielding gas composition on weld profile in pulsed Nd:YAG laser welding of low carbon steel
Weld area and weld depth/width ratio can be considered to be of the most important geometrical factors in pulsed laser welding. The effects of carbon dioxide and oxygen additions to the argon shielding gas on the weld properties in pulsed laser welding of low carbon steel is investigated. Presence of carbon dioxide and oxygen up to 10 and 15 percent respectively decreases the weld geometrical f...
متن کاملInvestigation of Microstructure weld zone of Hastelloy X Pulsed Nd-YAG laser welds
In the present study, the microstructure of welded zone of Hastelloy X sheets with thickness of 1 mm via pulsed Nd-YAG laser welding were studied. This welding process was done by autogenus and conductive method. Microstructure were observed by metallurgical OM and SEM. Results shown Solidification of the weld metal is dendritic. The dendrites in the central zone of the welding are fine and equ...
متن کاملApplication of YAG Pulsed Laser Micro-Welding in MEMS Packaging
This paper reports a new packaging method for a wide range of MEMS for application on both the wafer and device scale. Titanium is used as the packaging material in this work and both silicon and titanium MEMS devices are integrated on to a titanium substrate. A Nd:YAG pulsed laser is used to micro-weld the titanium cap to the substrate. A three-dimensional time dependent model of heat flow dur...
متن کاملOptimization of Operating Parameters for Autogenous Welding of AISI 316L Stainless Steel and Steel Using Pulsed Nd: YAG Laser
An attempt made to optimize the operating parameters involved in an autogenous pulsed Nd: YAG laser welding process of similar and dissimilar combinations of butt joint of 2 mm thick 316 L stainless steel and mild steel. Influence of prominent laser welding parameters such as average peak power, defocus position, spot position, and shielding gas were investigated for welded joints considered. T...
متن کاملLong-pulsed Nd : YAG laser: does it give clinical benefit on the treatment of resistant telangiectasia?
BACKGROUND Long-pulsed Nd : YAG laser has been used in treating larger and deep-seated leg veins. OBJECTIVE This study investigated the effectiveness and safety of long-pulsed Nd : YAG laser to treat alae nasae and nasal tip telangiectasia. METHODS Twelve patients were evaluated in a prospective IRB approved study. They had a history of previous unsatisfactory treatments with pulsed dye las...
متن کاملمنابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ذخیره در منابع من قبلا به منابع من ذحیره شده{@ msg_add @}
عنوان ژورنال
دوره 1 شماره 3
صفحات 35- 42
تاریخ انتشار 2013-07-01
با دنبال کردن یک ژورنال هنگامی که شماره جدید این ژورنال منتشر می شود به شما از طریق ایمیل اطلاع داده می شود.
میزبانی شده توسط پلتفرم ابری doprax.com
copyright © 2015-2023