Total Hip Arthroplasty with Modular Stem for Dysplastic Hips in South Asian Population
Authors
Abstract:
Introduction: Optimum component positioning and orientation is required to optimize the functional result during total hip arthroplasty for dysplastic hips. Patients and methods: Sixty-two patients (66 hips) including 33 males and 29 females underwent total hip arthroplasty using modular stem prosthesis at an average age of 40.6 years (range 17 to 49 years). Nineteen hips were classified as Type I, 24 hips as Type II, 13 hips as Type III and 10 hips as Type IV dysplastic hips according to Crowe’s classification. Eighteen hips (27.2%) underwent sub trochanteric osteotomy and 23 hips (34.8%) required adductor tenotomy at the time of surgery. Results: Sixty-one patients (65 hips) were available for the latest follow up. The median follow-up was 57.4 months (range12 to 100 months). The mean Harris Hip Score was 90.6 (range 72 to 96) which was significant improvement from the preoperative Score of 44.8 (range 38 to 62). The clinical outcome was graded as excellent in 39, good in 13, fair in 7 patients and poor in 2 patients respectively. Only one hip (1.5%) had underwent revision surgery for the stem at 18 months following the index surgery. Postoperative dislocation following a fall was seen in one hip of a female patient who was operated on both sides. The radiographs revealed that all the remaining 65 hips had stable femoral component and the osteotomy sites were healed. The Kaplan-Meier survivorship with revision as endpoint (including open reduction for dislocation) was found to be 96.4% at 100 months (95% Confidence Interval; 86.3-99.1). Conclusion: This study in South-Asian patients using the modular stem strengthened the premise that cementless modular total hip arthroplasty provides a satisfactory outcome in treating secondary osteoarthritis due to dysplastic hips.
similar resources
Cementless total hip arthroplasty for dysplastic and dislocated hips.
OBJECTIVES We evaluated the clinical and radiographic results of exclusively the same type and standard sized cementless total hip prostheses applied to all dysplastic and dislocated hips. PATIENTS AND METHODS In this study, we retrospectively reviewed 69 patients' (63 females, 6 males; mean age 45.6 years; range 20 to 72 years) 103 dysplastic or dislocated hips on which cementless total hip ...
full textTotal hip arthroplasty for arthodesed hips.
The benefits of converting an ankylosed or arthrodesed hip to total hip arthroplasty have been reported in the literature as have the technical difficulties associated with this procedure. This review, however, outlines the experience of a single surgeon (WJMB) at a single institution using uncemented prostheses. Between November 1991 and June 1996, 5 arthrodesed hips underwent uncemented total...
full textTotal hip arthroplasty for fused hips.
Arthrodesis of the hip has been used extensively in the past as the procedure of choice for many disabling diseases of the hip.1-4 A successful arthrodesis should provide a stable, painless hip. After hip fusion, patients usually have a short leg and will walk with a slightly slower pace than an individual with normal hips. They will likely walk with a perceptible limp and a gait described as a...
full textTotal Hip Arthroplasty Using S-ROM Prosthesis for Dysplastic Hip
PURPOSE The purpose of this study was to evaluate the clinical and radiological results of total hip arthroplasty using a proximal modular femoral stem in patients who had secondary coxarthrosis associated with a dysplastic hip. MATERIALS AND METHODS Forty-two patients (45 hips) with secondary coxarthrosis were evaluated after undergoing primary total hip arthroplasty using an S-ROM proximal ...
full textCeramic Surface Engineered Metal-on-Metal Hips system for Total Hip Arthroplasty and Resurfacing Hip Arthroplasty
components for the reconstruction of the acetabulum and metal femoral head components for conventional THA and RHA. The ACCIS®metal components are made of a chrome-cobalt-molybdenum alloy, but are different from other metal-on-metal prostheses. The surfaces of the metal components are engineered with the ceramic Titanium-Niobium-Nitride (TiNbN) in order to minimize metal particulate wear, to pr...
full textMy Resources
Journal title
volume 7 issue 6
pages 0- 0
publication date 2019-11-01
By following a journal you will be notified via email when a new issue of this journal is published.
Hosted on Doprax cloud platform doprax.com
copyright © 2015-2023