Optimization of Material Removal Rate in Electrical Discharge Machining Alloy on DIN1.2080 with the Neural Network and Genetic Algorithm

Authors

  • Amin Kolahdooz Assistant Professor, Young Researchers and Elite Club, Islamic Azad University, Khomeinishahr Branch, Isfahan/Khomeinishahr, Iran
  • Masoud Azimi MSc Student, Department of Mechanical engineering, Islamic Azad University, Khomeinishahr Branch, Isfahan/Khomeinishahr, Iran
  • Seyyed Ali Eftekhari Assistant Professor, Young Researchers and Elite Club, Islamic Azad University, Khomeinishahr Branch, Isfahan/Khomeinishahr, Iran
Abstract:

Electrical discharge machining process is one of the most Applicable methods in Non-traditional machining for Machining chip in Conduct electricity Piece that reaching to the Pieces that have good quality and high rate of machining chip is very important. Due to the rapid and widespread use of alloy DIN1.2080 in different industry such as Molding, lathe tools, reamer, broaching, cutting guillotine, etc. Reaching to optimum condition of machining is very important. Therefore the main aim in this article is to consider the effect of input parameter such voltage, Current strength, on-time pulse and off-time pulse on the machining chip rate and optimizing this in the electrical discharge machining for alloy DIN1.2080. So to reach better result after doing some experiments to predict and optimize the rate of removing chip, neural network method and genetic algorithm are used. Then optimizing input parameters to maximize the rate of removing chip are performed. In this condition, by decreasing time, the product cost is decreased. Optimum parameters in this experiment in this condition are obtained under Current strength 20 ampere, 160 volt, on-time pulse 100 micro second and off-time pulse 12 micro second that is obtained 0.063 cm3/min as rate of machining chip. After doing experiment, surveying the level of error and its accuracy are evaluated. According to the obtained error value that is about 5.18%, used method is evaluated for genetic algorithm

Upgrade to premium to download articles

Sign up to access the full text

Already have an account?login

similar resources

Comparative Neural Network Models on Material Removal Rate and surface Roughness in Electrical Discharge Machining

Electro-discharge machining (EDM) is increasingly being used in many industries for producing molds and dies, and machining complex shapes with material such as steel, cemented carbide, and engineering ceramics. The stochastic nature of EDM process has frustrated number of attempts to model it physically. Artificial neural networks (ANNs), as one of the most attractive branches in Artificial In...

full text

An Optimization on the DIN1.2080 Alloy in the Electrical Discharge Machining Process Using ANN and GA

Electrical Discharge Machining (EDM) process is one of the most widely used methods for machining. This method is used to form parts that conduct electricity. This method of machining has used for hard materials and therefore selects the correct values of parameters which are so effective on the quality machining of parts. Reaching to optimum condition of the DIN1.2080 alloy (D3) machining is v...

full text

An Optimization on the DIN1.2080 Alloy in the Electrical Discharge Machining Process Using ANN and GA

Electrical Discharge Machining (EDM) process is one of the most widely used methods for machining. This method is used to form parts that conduct electricity. This method of machining has used for hard materials and therefore selects the correct values of parameters which are so effective on the quality machining of parts. Reaching to optimum condition of the DIN1.2080 alloy (D3) machining is v...

full text

Optimization of Process Parameters on Material Removal Rate through Electro Discharge Machining

Among all non-conventional micro-machining, electrochemical discharge machining (ECDM) is having high quality of material removal rate with zero residual stress. This machining has been accepted as a highly modern technology in micromachining. In this paper an effort has been done on micro drilling of glass using electrochemical discharge machining (ECDM). A fixed tool and a step down transform...

full text

Investigation on the Material Removal Mechanism and the Thermal Aspects in the Electrical Discharge Machining Process

The aim of this paper is to study the Electro discharge machining process. EDM has been an important manufacturing process for the tool, mould, and dies industries for several decades. The process is finding an increasing industrial use owing to its ability to produce geometrically complex shapes as well as its ability to machine hard materials that are extremely difficult using conventional pr...

full text

Metal Removal Rate Optimization in Electric Discharge Machining Process

Electrical discharging machining (EDM) has become an outstanding approach in the field of metal cutting especially for conductive metals. It’s very difficult to cut the conducting metals with the aid of traditional machining. The main object of the present work has to investigate the effects of various EDM input parameters like pulse on time (Ton) pulse off time (TOFF) as well as the influence ...

full text

My Resources

Save resource for easier access later

Save to my library Already added to my library

{@ msg_add @}


Journal title

volume 9  issue 1

pages  77- 92

publication date 2016-04-20

By following a journal you will be notified via email when a new issue of this journal is published.

Hosted on Doprax cloud platform doprax.com

copyright © 2015-2023