Investigating Nonlinear Vibration Behavior of Rotors with Asymmetry Shaft Considering Misalignment
Authors
Abstract:
In this paper, the nonlinear vibration behavior of a rotor with asymmetric shaft considering misalignment is studied. The system consists of a rectangular shaft and a disk which is connected to a motor through a flexible coupling. In order to consider higher order deformations, nonlinear Bernoulli beam is used for modeling the shaft. Gibbons’ equations are utilized to apply misaligned coupling forces. The equations of motion of the system are derived using the Lagrangian method and then discretized by the Rayleigh-Ritz method. In order to solve nonlinear equations and hence obtaining nonlinear responses, multiple scales method is used. The vibration behavior of the system near the resonance frequencies is studied by taking into account various parameters including unbalance forces and the effect of the asymmetry of cross section of the shaft. The analytical results are consistent with those of numerical method with a good accuracy. In addition, the effects of variations of the system parameters on the rotor vibration behavior have been shown graphically. In the end, the changes in the various parameters of the system and their effects on the rotor vibration response are discussed.
similar resources
Shaft Misalignment and Vibration - A Model
Misalignment of coupled rotating machinery shafts is a frequently occurring problem which can have a substantial influence on equipment reliability. Experience has shown that diagnosis of misalignment through vibration analysis can be extremely difficult due in large part to the observed substantial variability in the character of machinery vibration even when apparently identical alignment sta...
full textShaft Misalignment Detection using Stator Current Monitoring
This paper inspects the misaligned of shaft by using diagnostic medium such as current and vibration. Misalignments in machines can cause decrease in efficiency and in the long-run it may cause failure because of unnecessary vibration, stress on motor, bearings and short-circuiting in stator and rotor windings. In this study, authors investigate the onset of instability on a shaft mounted on jo...
full textNonlinear Vibration Analysis of a cantilever beam with nonlinear geometry
Analyzing the nonlinear vibration of beams is one of the important issues in structural engineering. According to this, an impressive analytical method which is called Modified Iteration Perturbation Method (MIPM) is used to obtain the behavior and frequency of a cantilever beam with geometric nonlinear. This new method is combined by the Mickens and Iteration methods. Moreover, this method don...
full textVibration Analysis of Rotating Shaft with Loose Disk
In this paper energy method is used to calculate rotor response with loose rotating disk on it. System equation of motion is obtained based on energy method and Lagrange equation. Mathematical modeling of loose disk in a rotor bearing system has resulted in terms similar to unbalance and gyroscopic effect in the system equation of motion. The effect of loose disk axial position and orthotropic ...
full textA Review on Vibration Analysis for Misalignment of Shaft in Rotary Systems by Using Discrete Wavelet Transform
A Review on Vibration Analysis for Misalignment of Shaft in Rotary Systems by Using Discrete Wavelet Transform Abhijeet Shirude | S. Y. Gajjal (Mechanical Department, NBNSSoE, Savitribai Phule Pune University, Pune, India, [email protected]) (Mechanical Department, NBNSSoE, Savitribai Phule Pune University, Pune, India, [email protected]) ___________________________________________...
full textNonlinear Vibration Analysis of Composite Plates with SMA Wires, Considering Instantaneous Variations of the Martensite Volume Fraction
In the past few years, extensive improvements have been accomplished in reinforcing the structures through using shape memory alloys (SMAs). These materials absorb or dissipate energy through establishing a reversible hysteresis loop during a cyclic mechanical loading. This unique characteristic of the SMAs has made them appropriate for sensing, actuation, absorbing the impact energy, and vibra...
full textMy Resources
Journal title
volume 11 issue 3
pages 535- 549
publication date 2019-09-30
By following a journal you will be notified via email when a new issue of this journal is published.
Hosted on Doprax cloud platform doprax.com
copyright © 2015-2023