IN-SITU FABRICATION PROCESS OF AL- TIC COMPOSITE BY SLAG
Authors
Abstract:
The new in situ method for AI-TiC composite fabrication has been carried out. In this method, fabrication of AI-TiC composite by simultaneous introduction of titanium oxide and carbon into aluminum melt was investigated.. Under the process conditions, titanium and carbon reaction results in titanium carbide whiskers. The salt containing keriolite (Na3AIF6), titanium oxide (TiO2) and graphite used for this purpose. Using Scanning Electron Microscopy (SEM) and X-Ray Diffraction analysis (XRD) the resulted composite was characterized. It was shown that it contains Al as matrix and TiC as the reinforcement. Then, mechanical properties of fabricated composite were examined.
similar resources
IN SITU FABRICATION OF Al 2024-Mg2Si COMPOSITE BY SPARK PLASMA SINTERING OF REACTIVE MECHANICALLY ALLOYED POWDER
In situ Al2024- Mg2Si composite was fabricated by spark plasma sintering (SPS) of reactive powder. Reactive powder was obtained from mechanical alloying (MA) of elemental powders. Clad layers of in situ composite were fabricated on Al substrates by spark plasma sintering (SPS). Structural evolution during MA process and after SPS was investigated by X-ray diffractometery (XRD). Scanning electro...
full textPilot in-Situ Production of AL-TiB2 and AL-ZrB2 Composites Using Reactive Slag
In this research work, the possibility of semi industrial production of Al-TiB2 and Al-ZrB2 composites, using reactive slag in a flame furnace have been investigated. For this purpose, commercial pure aluminum and powder mixture of TiO2 (ZrO2) , KBF4 and Na3AlF6 were used. The results showed that using a proper ratio of slag forming materials as well as proper amounts of the above-mentioned com...
full textPilot in-Situ Production of AL-TiB2 and AL-ZrB2 Composites Using Reactive Slag
In this research work, the possibility of semi industrial production of Al-TiB2 and Al-ZrB2 composites, using reactive slag in a flame furnace have been investigated. For this purpose, commercial pure aluminum and powder mixture of TiO2 (ZrO2) , KBF4 and Na3AlF6 were used. The results showed that using a proper ratio of slag forming materials as well as proper amounts of the above-mentioned com...
full textFabrication of in situ TiC reinforced aluminum matrix composites
In the present work, the room and elevated temperature mechanical behavior of Al/TiC, high-strength Al-Si/TiC and the elevated temperature-resistant Al-Fe(-V-Si)/TiC composites has been evaluated. The microstructural characteristics of ingot metallurgy (IM) or rapid solidification (RS) Al-Si/TiC and Al-Fe(-V-Si)/TiC composites could be thought of as a combination of the related alloy matrix mic...
full textFabrication of TiC particulate reinforced Ni-50Fe super alloy matrix composite powder by mechanical alloying
Mechanical alloying is a powder metallurgy processing technique involving cold welding, fracturing, and rewelding of powder particles in a high-energy ball mill. In this work, NiFe-TiC composite powders were prepared by mechanical alloying process using planetary high-energy ball mill. The effect of TiC addition by weight percent on the NiFe solid solution formation, grain size, lattice paramet...
full textFabrication and Mechanical Properties of Iron Slag Matrix Composite Materials
–The objective of present work is to use this industrial waste i.e. Slag as particulate filler material to the epoxy matrix composites by molding technique with different weight fractions ( 0%, 5%,10%,15%, 20% ) to study the mechanical behaviour of reinforced polymer composite material. The change in weight is studied for Slag under different tests like, tensile, bending and impact for obtainin...
full textMy Resources
Journal title
volume 1 issue 2
pages 9- 15
publication date 2004-06
By following a journal you will be notified via email when a new issue of this journal is published.
No Keywords
Hosted on Doprax cloud platform doprax.com
copyright © 2015-2023