Evaluation of structural analysis of tunnel segmental lining using beam-spring method and force-method (Case study: Chamshir water conveyance tunnel)
Authors
Abstract:
The joints between segmental rings can withstand a certain amount of bending moment as well as axial and shear forces. Generally, in the structural analysis of tunnel segmental lining, the joints can be modeled as elastic hinges or rotational springs, and their rigidity should be demonstrated in terms of the rigidity of the joints or their rotational stiffness. Therefore, the bending moment acting on the tunnel lining is reduced. Hence, the tunnel designers are free to choose a lining with a lower cost. In this research work, especially considering the joints, the structural analysis of the segmental lining with variation in the flexural stiffness of the joints ( ), soil resistance coefficient ( ), number of segmental lining joints, and joint arrangement of segmental lining were carried out by the Force-Method equations. The imposed bending moment and axial forces were computed based on the Beam-Spring method, which is widely used to analyze the internal forces of segmental lining, and compared them with the results of the Force-Method equations. Then the effects of joint arrangement patterns and joint rotational spring stiffness on the results of the Beam-Spring analysis were evaluated. Finally, the optimum characteristics of the reinforced concrete segmental lining design were evaluated using the interaction diagram of bending moments and axial forces. The results obtained showed that the presented pattern for the segmental lining at the Chamshir tunnel was imposed against the external pressures on the segmental lining with an acceptable safety factor.
similar resources
evaluation of structural analysis of tunnel segmental lining using beam-spring method and force-method (case study: chamshir water conveyance tunnel)
the joints between segmental rings can withstand a certain amount of bending moment as well as axial and shear forces. generally, in the structural analysis of tunnel segmental lining, the joints can be modeled as elastic hinges or rotational springs, and their rigidity should be demonstrated in terms of the rigidity of the joints or their rotational stiffness. therefore, the bending moment act...
full textTunnel Rehabilitation in Fault Zone Using Sequential Joints Method- Case Study: Karaj Water Conveyance Tunnel
The lining structure of Tunnel Boring Machine (TBM) excavated tunnels is composed of series of precast Reinforced Concrete (RC) pieces which are called segment. At the present paper, a novel method is introduced for seismic retrofitting of segmental tunnels located at active fault zones in rock environment with case study of Amirkabir dam to Tehran water transfer tunnel (Karadj tunnel). The mai...
full textPrediction of structural forces of segmental tunnel lining using FEM based artificial neural network
To judge about the performance of designed support system for tunnels, structural forces i.e. peak values of axial and shear forces and moments are critical parameters. So in this study, at first a complete database using finite element method was prepared. Then, a model of artificial neural network (ANN) using multi-layer perceptron was developed to estimate lining structural forces. Sensitivi...
full textEffect of Segmental Joint on Internal Forces in Tunnel Lining under Seismic Loading by Numerical Method
Although segmental tunnel linings are often used for seismic areas, the influence of segment joints on the segmental lining behavior under seismic loading has not been thoroughly considered in the literature. This paper presents the results of a numerical study investigating the effects of the rotational, axial, and radial joint stiffness of the longitudinal joints on the structural force...
full textEffect of segmental joint stiffness on tunnel lining internal forces under static conditions
According to the wide application of segmental lining in mechanized tunneling, recognizing the behavior of segmental lining joints is important in tunnels designing. In the structural analysis of the tunnel segmental lining, segmental joints can be considered as elastic joints, and their stiffness characteristics are affected by the rotational, shear, and axial stiffness. The purpose of this wo...
full textMy Resources
Journal title
volume 8 issue 1
pages 111- 130
publication date 2017-01-01
By following a journal you will be notified via email when a new issue of this journal is published.
Keywords
Hosted on Doprax cloud platform doprax.com
copyright © 2015-2023