Comparative Analysis of Dimensional Accuracy of Two Types of Silicone Impression Materials: Optosil and Elite-HD
Authors
Abstract:
Statement of the Problem: Understanding about impression materials, their properties, uses and manipulation can guide operators towards having more successful restorations. Purpose: The aim of this in vitro study was to compare the accuracy of a condensation silicone impression material, Optosil, and an addition poly siloxane impression material, Elite-HD. Materials and Method: A laboratory model with two metallic dies was used to make impression. A horizontal notch on one of the two dies simulated an undercut. Ten impressions were made by each impression material by the putty-wash technique. After pouring impressions with velmix die stone, a total of 20 stone casts were made from both materials. Measurements of casts were compared with the master model. Statistical analyses were performed using t-test. Result: This results of this study showed that the height of die without undercut decreased in both groups. Also the height above the undercut decreased in both groups, which was more obvious in Elite-HD group than Optosil group. The distance between dies increased in both groups, with higher figures for Elite-HD. So, Optosil is a more accurate material for registering inter-abutment distance than Elite-HD. The diameter of die under the undercut decreased in Optosil group and was similar to the master model in Elite-HD. Statistical analysis showed significant differences between these two groups in the distance between abutments (p=0.001), the diameter of die under the undercut (p=0.014) and the height of die above undercut(p=0.057). Conclusion: Optosil is more accurate in registering inter-abutment distance than Elite-HD, so Optosil is preferred for fixed partial denture impressions. Since Elite-HD showed more accuracy in C measurements than Optosil, it is preferred for single crown impressions.
similar resources
a comparative analysis of the marginal microleakages of two pit and fissure sealans, conseal-f and conseal clear
چکیده ندارد.
15 صفحه اولA comparison of the accuracy and dimensional stability between two silicon impression materials (Speedex and Irasil)
A comparison of the accuracy and dimensional stability between two silicon impression materials (Speedex and Irasil) Dr. M. Sabouhi* - Dr. M. Dakhilalian** - Dr. N. Nehchiri*** *- Assistant Professor of Fixed Prosthodontics Dept. - Faculty of Dentistry – Isfahan University of Medical Sciences. **- Member of Fixed Prosthodontics Dept. - Faculty of Dentistry – Isfahan University of Medical Scienc...
full texttransference of imagery: a comparative formalistic study of shakespeares hamlet and its two persian translations
هدف از این تحقیق بررسی انتقال صور خیال هملت در دو ترجمه ی فارسی آن از نظر فرمالیستی بود. برای بدست آوردن داده-های مورد نیاز، 130 نمونه استعاره، مجاز، ایهام، کنایه و پارادوکس در متن اصلی مشخص شده و سپس بر اساس مدل نیومارک (1998) برای ترجمه ی استعاره یا بطور کلی زبان مجاز با معادل های فارسی شان مقایسه گردیدند. این تحقیق بر آن بود تا روش های استفاده شده برای ترجمه هر کدام از انواع زبان مجاز ذکر شد...
15 صفحه اولcomparative analysis of the use of hedges & emphatics in english and persian academic research articles of sociology & psychology
چکیده ندارد.
15 صفحه اولDimensional accuracy of 3 silicone dental impression materials.
This study was carried out to measure the dimensional changes in silicone impression material, which can affect the fitness of the prosthesis. Using both single and double mix techniques, 20 impression samples for each of 3 different proprietary silicones, Xantopren-H, President and Fulldent, were made. Selected measurements were made on the stone casts made from each impression. In all 3 cases...
full textDimensional accuracy of three impression materials by one-step and two-step impression techniques: An in vitro study
Introduction: An accurate impression is essential to create a well-fitted dental prosthesis. This study aimed to compare the dimensional accuracy of three elastomeric materials using one-step and two-step impression techniques. Methods: In this study, 20 impressions were fabricated for each Vinyl siloxane ether (Identium), condensation silicone (Speedex), and a...
full textMy Resources
Journal title
volume 6 issue 1
pages 1- 6
publication date 2017-03-01
By following a journal you will be notified via email when a new issue of this journal is published.
Hosted on Doprax cloud platform doprax.com
copyright © 2015-2023