ANALYTICAL STUDY OF STEEL I-BEAM WITH STEPPED FLANGES

Authors

  • C. B. Nayak
  • F. P. Kumthekar
  • S. G. Morkhade
Abstract:

This paper presents a parametric study of steel I- beam with stepped flanges by using finite element analysis. Stepped flange beam is used in structures to decrease the negative bending moments near interior supports that causes failure due to buckling. Steps in the cross section can be achieved by adding cover plates to the beam flanges, changing the size of the hot rolled section, or changing the flange thickness and/or width for built-up section. The stress concentration with variation in stepped beam configuration such as doubly and singly stepped I-beams has been examined thoroughly. The loadings are limited to those having an inflection point of zero under point load at mid span. Beams with degree of symmetry, ρ of 0.2 are investigated for the present study. Unbraced length to height ratio of the beam to be analyzed is considered as 15. In addition, to check the effect of steps, stepped parameters α, β and γ are varied. The results shows that, a change of flange thickness is more significant than a change of flange width on the lateral torsional buckling capacity of a singly stepped beam.

Upgrade to premium to download articles

Sign up to access the full text

Already have an account?login

similar resources

New Mathematical Modeling of Steel Panel Zone with Thin to Thick Column Flanges

The response of a steel moment resisting frame (MRF) depends on the specifications of its main components, namely the columns, beams and connections. One important connection element which can significantly affect frame behavior is the panel zone (PZ). The PZ is described to be an element mainly subjected to shear stresses and its failure mode is often governed by shear yielding. Several analyt...

full text

Analytical and Experimental Investigation of I Beam-to-CFT Column Connections under Monotonic Loading (RESEARCH NOTE)

In this study, the behavior characteristics of I beam-to-concrete filled tube (CFT) column connection is studied through experiment and finite element models under the monotonic loading. To validate the finite element modeling, at first, an experimental model is made and experimented. After validation of the finite element modeling, different models were created in the software. The studied par...

full text

non-linear study of various slit shear walls in steel structures

seismic retrofit strategies have been developed in the past few decades following the introduction of new seismic provisions and the availability of advanced materials and methods. it can be observed that new approaches to deal with more lateral forces are more innovative and more energy absorbent. in line with this, there is a growing trend toward the use of steel shear walls as a system with ...

15 صفحه اول

Study on Distortion of Bi-Steel Concrete Beam

As an economic and safe structure, Bi-steel is widely used in reinforced concrete with less consumption of steel. In this paper, III Bi-steel concrete beam has been analyzed. Through careful observation and theoretical analysis, the new calculating formulae for structural rigidity and crack have been formulated for this Bi-steel concrete beam. And structural rigidity and the crack features have...

full text

Design aspects of steel I-girders with corrugated steel webs

Corrugated web girders represent a new structural system emerged in the past two decades. The girder’s flanges provide the flexural strength of the girder with no contribution from the corrugated web which provides the girder’s shear capacity. Failure of the web occurs by steel yielding, web buckling or interactively between them. Lateral torsion and local flange buckling of corrugated web gird...

full text

study of dna interaction with ethylenediaminetetraacetic acid and sesamol food additives

برهمکنش dnaتیموس گاوی طبیعی (ct-dna) با اتیلن دی آمین تترااستات (edta)در بافرtris-hcl با 8/7 ph ( دراین ph،edta به نمک دی سدیم تبدیل می شود) وسسامول در بافر tris-hcl با4/7 ph مورد بررسی قرار گرفته است. edta و سسامول استفاده فراوانی در تکنولوژی غذایی و صنعت شیمیایی دارند. مدل اتصال dna مربوط بهedta بوسیله اسپکتروفتومتری جذب، دورنگ نمایی حلقوی(cd)، ویسکومتری وژل الکتروفورز بررسی شده است. طیفuv ...

15 صفحه اول

My Resources

Save resource for easier access later

Save to my library Already added to my library

{@ msg_add @}


Journal title

volume 10  issue 2

pages  217- 229

publication date 2020-04

By following a journal you will be notified via email when a new issue of this journal is published.

Keywords

Hosted on Doprax cloud platform doprax.com

copyright © 2015-2023