Analysis of deep drawing process to predict the forming severity considering inverse finite element and extended strain-based forming limit diagram

Authors

Abstract:

An enhanced unfolding Inverse Finite Element Method (IFEM) has been used together with an extended strain-based forming limit diagram (EFLD) to develop a fast and reliable approach to predict the feasibility of the deep drawing process of a part and determining where the failure or defects can occur. In the developed unfolding IFEM, the meshed part is properly fold out on the flat sheet and treated as a 2D problem to reduce the computation time. The large deformation relations, nonlinear material behavior and friction conditions in the blank holder zone have also been considered to improve the accuracy and capability of the proposed IFEM. The extended strain-based forming limit diagram based on the Marciniak and Kuczynski (M-K) model has been computed and used to predict the onset of necking during sheet processing. The EFLD is built based on equivalent plastic strains and material flow direction at the end of forming. This new forming limit diagram is much less strain path dependent than the conventional forming limit diagram. Furthermore, the use and interpretation of this new diagram are easier than the stress-based forming limit diagram. Finally, two applied examples have been presented to demonstrate the capability of the proposed approach.

Upgrade to premium to download articles

Sign up to access the full text

Already have an account?login

similar resources

Numerical Determination of the Forming Limit Diagram for 304 Stainless Steel Based on Phase Change in Deep Drawing Process

Up to now a large number of models have been developed to measure or predict the damage in equipments. Some of these models have been implemented in ABAQUS software. To implement damage parameters in the software, it is necessary to perform complex and expensive practical tests. One of these damage models is Forming Limit Diagram (FLD).The purpose of this research is deriving required parameter...

full text

Determination of Buckling Limit of Strain in Cold Roll Forming through Finite Element Analysis

In this study, Buckling Limit of Strain (B.L.S.) is introduced as one of the most important limiting factors in cold roll forming process. B.L.S. is calculated by the finite element procedure. Then for two particular processes with existing analysis and experimental results, B.L.S. has been determined and evaluated. LUSAS 12.3 is used for finite element analysis. The results show that when buck...

full text

Determination of Buckling Limit of Strain in Cold Roll Forming through Finite Element Analysis

In this study, "Buckling Limit of Strain" (B.L.S.) is introduced as one of the most important limiting factors in cold roll forming process. B.L.S. is calculated by the finite element procedure. Then for two particular processes with existing analysis and experimental results, B.L.S. has been determined and evaluated. LUSAS 12.3 is used for finite element analysis. The results show that when bu...

full text

Evaluation of Forming Severity and Thickness Variation in Deep Drawing Process

This paper presents a new methodology for complete solution of general shape deep drawn parts. Evaluation of forming severity, estimation of the punch load and prediction of the thickness variation are the major results obtained in this work. The punch work is the summation of the homogenous work of flange deformation and bending and frictional works. To evaluate the strain energy of the flange...

full text

Optimization of the strain distribution in the roll forming process using the desirability function and finite element methods

Defects of the roll forming process are affected by amount and situation of the strains distribution. The effect of the process parameters on the strain distribution in the round cross section roll forming process has been studied. Finite element and response surface method have been used for process modelling. Then desirability functions approach and overlaid counter plots have been employed f...

full text

Analytical and Finite Element Analysis of Hydroforming Deep Drawing Process

This paper gives an overview of a deep drawing process by pressurized liquid medium separated from the sheet by a rubber diaphragm. Hydroforming deep drawing processing of sheet metal parts provides a number of advantages over conventional techniques. It generally increases the depth to diameter ratio possible in cup drawing and minimizes the thickness variation of the drawn cup. To explore the...

full text

My Resources

Save resource for easier access later

Save to my library Already added to my library

{@ msg_add @}


Journal title

volume 8  issue 1

pages  39- 48

publication date 2018-09-01

By following a journal you will be notified via email when a new issue of this journal is published.

Hosted on Doprax cloud platform doprax.com

copyright © 2015-2023