The Fringe-Capacitance of Etching Holes for CMOS-MEMS
نویسندگان
چکیده
Movable suspended microstructures are the common feature of sensors or devices in the fields of Complementary-Metal-Oxide-Semiconductors and Micro-Electro-Mechanical Systems which are usually abbreviated as CMOS-MEMS. To suspend the microstructures, it is commonly to etch the sacrificial layer under the microstructure layer. For large-area microstructures, it is necessary to design a large number of etching holes on the microstructure to enhance the etchant uniformly and rapidly permeate into the sacrificial layer. This paper aims at evaluating the fringe capacitance caused by etching holes on microstructures and developing empirical formulas. The formula of capacitance compensation term is derived by curve-fitting on the simulation results by the commercial software ANSYS. Compared with the ANSYS simulation, the deviation of the present formula is within ̆5%. The application to determine the capacitance of an electrostatic micro-beam with etching holes is demonstrated in a microstructure experiment, which agrees very well with the experimental data, and the maximum deviation is within ̆8%. The present formula is with simple form, wide application range, high accuracy, and easy to use. It is expected to provide the micro-device designers to estimate the capacitance of microstructures with etching holes and predominate in the device characteristics.
منابع مشابه
Fabrication and Characterization of a New MEMS Capacitive Microphone using Perforated Diaphragm
In this paper, a novel single-chip MEMS capacitive microphone is presented. The novelties of this method relies on the moveable aluminum (Al) diaphragm positioned over the backplate electrode, where the diaphragm includes a plurality of holes to allow the air in the gap between the electrode and diaphragm to escape and thus reduce acoustical damping in the microphone. Spin-on-glass (SOG) was us...
متن کاملFabrication and Characterization of CMOS-MEMS Magnetic Microsensors
This study investigates the design and fabrication of magnetic microsensors using the commercial 0.35 μm complementary metal oxide semiconductor (CMOS) process. The magnetic sensor is composed of springs and interdigitated electrodes, and it is actuated by the Lorentz force. The finite element method (FEM) software CoventorWare is adopted to simulate the displacement and capacitance of the magn...
متن کاملCapacitive Drive and Detection of MEMS Resonant Motion: Electrical Integration of MEMS
Incorporation of microelectromechanical system (MEMS) oscillators into devices has been limited by the lack of an easily-integrated motional detection scheme. A capacitive detection scheme enabled by impedance matching techniques has been demonstrated for nanowires. However, no measurement had been demonstrated in micron-scale oscillators of interest in sensor and electrical filter applications...
متن کاملDesign of Novel High Sensitive MEMS Capacitive Fingerprint Sensor
In this paper a new design of MEMS capacitive fingerprint sensors is presented. The capacitive sensor is made of two parallel plates with air gap. In these sensors, the capacitance changes is very important factor. It is caused by deformation of the upper electrode of sensor. In this study with making slots in upper electrode, using T-shaped protrusion on diaphragm in order to concentrate the f...
متن کاملModeling of capacitance and sensitivity of a MEMS pressure sensor
In this paper modeling of capacitance and sensitivity for MEMS capacitive pressure sensor is presented. In capacitive sensor the sensitivity is proportional to deflection and capacitance changes versus pressure. Therefore first the diaphragm displacement, capacitance and sensitivity of sensor with square diaphragm have been modeled and then simulated using finite element method (FEM). It can b...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید
ثبت ناماگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید
ورودعنوان ژورنال:
- Micromachines
دوره 6 شماره
صفحات -
تاریخ انتشار 2015