The impact of hot melt extrusion and spray drying on mechanical properties and tableting indices of materials used in pharmaceutical development.

نویسندگان

  • Raman Iyer
  • Shridhar Hegde
  • Yu-E Zhang
  • James Dinunzio
  • Dharmendra Singhal
  • A Malick
  • Gregory Amidon
چکیده

The impact of melt extrusion (HME) and spray drying (SD) on mechanical properties of hypromellose acetate succinate (HPMCAS), copovidone, and their formulated blends was studied and compared with that of reference excipients. Tensile strength (TS), compression pressure (CP), elastic modulus (E), and dynamic hardness (Hd ) were determined along with Hiestand indices using compacts prepared at a solid fraction of ∼0.85. HPMCAS and copovidone exhibited lower Hd , lower CP, and lower E than the reference excipients and moderate TS. HPMCAS was found to be highly brittle based on brittle fracture index values. The CP was 24% and 61% higher for HPMCAS after SD and HME, respectively, than for unprocessed material along with a higher Hd . Furthermore, the TS of HPMCAS and copovidone decreased upon HME. Upon blending melt-extruded HPMCAS with plastic materials such as microcrystalline cellulose, the TS increased. These results suggest that SD and HME could impact reworkability by reducing deformation of materials and in case of HME, likely by increasing density due to heating and shear stress in a screw extruder. A somewhat similar effect was observed for the dynamic binding index (BId ) of the excipients and formulated blends. Such data can be used to quantitate the impact of processing on mechanical properties of materials during tablet formulation development.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Hot-Melt Extrusion Technique: A Review

Hot-melt extrusion is one of the most widely applied processing technologies in the plastic, rubber and food industry. Today this technology has found its place in the array of pharmaceutical manufacturing operations. Melt extrusion process are currently applied in the pharmaceutical field for the manufacture of a variety of dosage forms and formulations such as granules, pellets, tablets, supp...

متن کامل

Hot-Melt Extrusion Technique: A Review

Hot-melt extrusion is one of the most widely applied processing technologies in the plastic, rubber and food industry. Today this technology has found its place in the array of pharmaceutical manufacturing operations. Melt extrusion process are currently applied in the pharmaceutical field for the manufacture of a variety of dosage forms and formulations such as granules, pellets, tablets, supp...

متن کامل

Improvement of Physico-mechanical Properties of Partially Amorphous Acetaminophen Developed from Hydroalcoholic Solution Using Spray Drying Technique

  Objective(s): This study was performed aiming to investigate the effect of particle engineering via spray drying of hydroalcoholic solution on solid states and physico-mechanical properties of acetaminophen.   Materials and Methods: Spray drying of hydroalcoholic solution (25% v/v ethanol/water) of acetaminophen (5% w/v) in the presence of small amounts of polyninylpyrrolidone K30 (PVP) (0, 1...

متن کامل

Effect of Particle Volume Fraction on the Tensile Properties of Composite Al6061/SiC Materials by Hot Extrusion

In the present study the effect of phase volume fraction on the reinforcement of microstructure and tensile properties of composite extrusion process Al6061/SiC has been studied. For this purpose, the base alloy Al6061 using pure aluminum ingots, silicon, of Al-50% Mg, Al-10% Cr and a thin copper rod was prepared. Next, the composite Al6061/5% SiC, Al6061/10% SiC, Al6061/15% SiC and Al6061/20% ...

متن کامل

Hot Melt Extrusion Technique

Various approaches have been adopted to address this including preparation of solid dispersions and solid solutions. Hot-melt extrusion is an efficient technology for producing solid molecular dispersions with considerable advantages over solvent-based processes such as spray drying and co-precipitation. Hot-melt extrusion has been demonstrated to provide sustained, modified, and targeted drug ...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • Journal of pharmaceutical sciences

دوره 102 10  شماره 

صفحات  -

تاریخ انتشار 2013