Gap Flows through Idealized Topography. Part II: Effects of Rotation and Surface Friction

نویسندگان

  • SAŠA GABERŠEK
  • DALE R. DURRAN
چکیده

Numerical simulations are conducted of geostrophically balanced flow over an isolated mountain cut by a horizontal gap. The relative importance of the along-gap synoptic-scale pressure gradient and terraininduced mesoscale circulations for the generation of gap winds was examined by changing the direction of the synoptic-scale wind relative to the topography. In all cases, the forcing associated with mesoscale circulations generated by the mountain was at least as significant as the synoptic-scale pressure gradient. In the cases where a component of the large-scale flow was directed perpendicular to the ridge, the dynamics were dominated by either the vertical momentum fluxes due to mountain lee waves or by mesoscale pressure gradients associated with upstream blocking or lee troughing. Mesoscale circulations were also important when the large-scale flow was parallel to the ridge because surface friction turned the low-level winds toward the high pressure side of the ridge, partially blocking the flow and enhancing the along-gap pressure gradient. The flow in the interior of a very long uniform gap was also simulated for a case with the synoptic-scale winds parallel to the ridge so that the synoptic-scale pressure gradient was down the gap. The flow in the interior of the long gap was not horizontal and not in a simple dynamical balance between acceleration, the pressure gradient force, and surface friction. Even the flow in the lowest 150 m was gradually subsiding. Subsidence and lateral momentum flux convergence at low levels near the center of the gap were important contributors to the mass and along-gap momentum budgets.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Joining of the 5083 aluminum alloy using the bobbin tool friction stir welding technique

Conventional fusion welding of aluminum alloys results in coarse-grained structure, inevitable defects, and significant softening in the welding region. Friction stir welding with bobbin tool is a technique of friction stir welding method that has a great potential for developing applications of friction stir welding method in marine, aerospace, and automotive industries due to having an extra ...

متن کامل

Joining of the 5083 aluminum alloy using the bobbin tool friction stir welding technique

Conventional fusion welding of aluminum alloys results in coarse-grained structure, inevitable defects, and significant softening in the welding region. Friction stir welding with bobbin tool is a technique of friction stir welding method that has a great potential for developing applications of friction stir welding method in marine, aerospace, and automotive industries due to having an extra ...

متن کامل

Simulation of Tool Rotation and Travelling Speed Effects on Friction Stir Welding of Ti-6Al-4V

In this research, the effects of parameters include tool rotational and traverse speeds were investigated on heat generation and material flow during friction stir welding of Ti-6Al-4V alloy with computational fluid dynamics (CFD) method. Simulation results showed that with increasing of tool rotational and decreasing tool traverse speed, the more frictional heat generates which causes formatio...

متن کامل

Gap Flows through Idealized Topography. Part I: Forcing by Large-Scale Winds in the Nonrotating Limit

Gap winds produced by a uniform airstream flowing over an isolated flat-top ridge cut by a straight narrow gap are investigated by numerical simulation. On the scale of the entire barrier, the proportion of the oncoming flow that passes through the gap is relatively independent of the nondimensional mountain height e, even over that range of e for which there is the previously documented transi...

متن کامل

Dry Friction and Wear Performance of Micro Surface Textures Generated by Ultrasonic Assisted Face Turning

Nowadays the surface texturing has been widely recognized as a usable capability to improve the tribological systems. In this paper, ultrasonic assisted turning (UAT) isperformed to create the micro textures on the flat faces. Micro surface texturing ismade on the Al7075-T6 by the UAT in the face turning process. Then, the influences of cutting speed feed, vibration direction and vibration ampl...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2005