Modification of Ni-Rich FCG NMC and NCA Cathodes by Atomic Layer Deposition: Preventing Surface Phase Transitions for High-Voltage Lithium-Ion Batteries
نویسندگان
چکیده
The energy density of current lithium-ion batteries (LIBs) based on layered LiMO2 cathodes (M = Ni, Mn, Co: NMC; M = Ni, Co, Al: NCA) needs to be improved significantly in order to compete with internal combustion engines and allow for widespread implementation of electric vehicles (EVs). In this report, we show that atomic layer deposition (ALD) of titania (TiO2) and alumina (Al2O3) on Ni-rich FCG NMC and NCA active material particles could substantially improve LIB performance and allow for increased upper cutoff voltage (UCV) during charging, which delivers significantly increased specific energy utilization. Our results show that Al2O3 coating improved the NMC cycling performance by 40% and the NCA cycling performance by 34% at 1 C/-1 C with respectively 4.35 V and 4.4 V UCV in 2 Ah pouch cells. High resolution TEM/SAED structural characterization revealed that Al2O3 coatings prevented surface-initiated layered-to-spinel phase transitions in coated materials which were prevalent in uncoated materials. EIS confirmed that Al2O3-coated materials had significantly lower increase in the charge transfer component of impedance during cycling. The ability to mitigate degradation mechanisms for Ni-rich NMC and NCA illustrated in this report provides insight into a method to enable the performance of high-voltage LIBs.
منابع مشابه
High‐Performance Heterostructured Cathodes for Lithium‐Ion Batteries with a Ni‐Rich Layered Oxide Core and a Li‐Rich Layered Oxide Shell
The Ni-rich layered oxides with a Ni content of >0.5 are drawing much attention recently to increase the energy density of lithium-ion batteries. However, the Ni-rich layered oxides suffer from aggressive reaction of the cathode surface with the organic electrolyte at the higher operating voltages, resulting in consequent impedance rise and capacity fade. To overcome this difficulty, we present...
متن کاملVoltage increase of aqueous lithium-ion batteries by Li-ion conducting Li1.5Al0.5Ge1.5(PO4)3 glass-ceramic
In this research, a lithium ion conducting lithium aluminum germanium phosphate (LAGP) glass-ceramic with a formula of Li1.5Al0.5Ge1.5(PO4)3 was synthesized by melt-quenching method and subsequent crystallization at 850 °C for 8 h. The prepared glass-ceramic was characterized using X-ray diffraction analysis (XRD) and field emission scanning electron microscopy (FESEM). The XRD patterns exhib...
متن کاملEngineering the surface of LiCoO2 electrodes using atomic layer deposition for stable high-voltage lithium ion batteries
متن کامل
Ultrathin surface modification by atomic layer deposition on high voltage cathode LiNi0.5Mn1.5O4 for lithium ion batteries
Atomic layer deposition (ALD) has been employed to modify the surface of high voltage cathode LiNi0.5Mn1.5O4 by coating ultrathin Al2O3 layer on the electrodes. The ultrathin layer of Al2O3 can suppress the undesirable reactions during cycling, while maintaining the electron and ion conductivity of the electrode. The ALD Al2O3 coated LiNi0.5Mn1.5O4 showed remarkable improvement over bare LiNi0....
متن کاملAtomic-Resolution Visualization of Distinctive Chemical Mixing Behavior of Ni, Co, and Mn with Li in Layered Lithium Transition- Metal Oxide Cathode Materials
Capacity and voltage fading of layered structured cathode based on lithium transition-metal oxide is closely related to the lattice position and migration behavior of the transition-metal ions. However, it is scarcely clear about the behavior of each of these transition-metal ions in this category of cathode material. We report direct atomic resolution visualization of interatomic layer mixing ...
متن کامل