Coverage Path Re-planning for Processing Faults

نویسندگان

  • Mykhaylo Nykolaychuk
  • Frank Ortmeier
چکیده

Currently, an automated surface treatment or finishing (e.g., abrasive blasting, cleaning or painting) is performed in two consecutive steps: first processing by tool, second quality evaluation by sensor. Often, a finished surface has defects like areas not properly processed. This is caused by path inaccuracy or errors in tool deployment. The defected areas can be detected only during a subsequent quality evaluation. As a result, a complete surface reprocessing is required which is costly and time-consuming. We propose a new approach that is a combination of surface treatment and quality evaluation processes in a single deployment. In our approach, an initial coverage path for surface treatment by a tool is given or calculated using a state-of-the-art coverage path planning algorithm. In fact, we extend an off-line generated initial coverage path with an ability to react to sensor-based defect recognitions during surface processing by a tool.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

FACTS: fault coverage estimation by test vector sampling

We propose a new statistical technique for estimating fault coverage in combinational circuits. Our method requires fault-free simulation of a random sample of vectors from the test vector set. Fault coverage is computed from controllabilities and observabilities both deened as probabilities and the method is applicable to any fault model like stuck-at-faults or delay faults. Experimental resul...

متن کامل

Statistical methods for delay fault coverage analysis

|We develop new statistical techniques for delay fault analysis. True value simulation is performed using a multi-value logic system describing signal states of two consecutive vectors. Signal statistics are used to estimate transition probabilities and observabilities. These allow us to estimate detection probabilities and the coverage for transition faults. For path delay faults, recognizing ...

متن کامل

A New Method for Improving Path Delay Fault Coverage

In the test of a circuit for faults it is very desirable to have the minimum paths that are to be tested for a complete circuit test. At first, the best test vectors are chosen and then these pairs of vectors are applied to the circuit. Each of these pair of vectors is able to detect a certain number of the faults and the path delay fault coverage for each and all of them may be calculated. Sui...

متن کامل

Improving accuracy in path delay fault coverage estimation

A recently published method computes path delay fault coverage from the count of the number of path faults newly sensitized by a simulated vector pair. Such an estimate is pessimistic since several paths may share a set of lines. In this paper, we present a continuum of approximate methods, approaching exact fault simulation, for a tradeoo between accuracy and complexity. Higher accuracy is obt...

متن کامل

Sampling-Based Coverage Path Planning for Inspection of Complex Structures

We present several new contributions in sampling-based coverage path planning, the task of finding feasible paths that give 100% sensor coverage of complex structures in obstaclefilled and visually occluded environments. First, we establish a framework for analyzing the probabilistic completeness of a sampling-based coverage algorithm, and derive results on the completeness and convergence of e...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2015