ARBS Annual Review of Biomedical Sciences

نویسندگان

  • Karen Moore
  • Aline Quadros Bonilla
چکیده

1 This article was supported by the Florida Agricultural Experimental Station. 2 Correspondence Karen Moore, Department of Animal Sciences, University of Florida, PO Box 110910, Gainesville, Florida 326110910, USA. E-mail: [email protected] Abstract Moore K, Bonilla AQ. Cryopreservation of Mammalian Embryos: the State of the Art. ARBS Annu Rev Biomed Sci 2006;8:19-32. Embryo cryopreservation has been a useful tool for embryology since the early 1970s. It has become an essential part of assisted reproductive technologies, allowing long term storage of valuable embryos from lab animals, livestock, endangered species and humans. Initially, work was done with conventional slow cooling technologies, using cryoprotectants, such as glycerol or ethylene glycol and sucrose. More recently, however, greater advances have been made with vitrification, a procedure that bypasses ice crystal formation and places the embryo in a glass-like state. This technology is receiving greater attention as it is simpler, faster and less expensive, and provides the embryo with greater protection from cryoinjury. Successful cryopreservation requires a good understanding of the proper use of cryoprotectants, sugars, and macromolecules in order to allow the highest survival rates and ultimately pregnancy and live offspring following embryo transfer. Although this technology has been in existence for over three decades, it still yields variable results. It is clear now that success is dependent upon many variables, including embryo stage and quality, embryo species and derivation, cooling and warming rates and culture conditions, to name a few. Efforts to optimize these conditions will further enhance survival and future developmental potential of the embryo. This review will briefly summarize the current understanding of embryo cryopreservation technologies, including key areas of concern and strategies to achieve the greatest successes, as well as possible future directions for this field. © by São Paulo State University – ISSN 1806-8774

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

ARBS Annual Review of Biomedical Sciences

1 Correspondence Dept. of Anatomy and Cell Biology, Shinshu University School of Medicine, Matsumto 390-8621, Japan, and Dept. of Anatomy, Shinshu Institute of Alternative Medicine, Nagano 380-0816, Japan. E-mail: [email protected] Abstract Nagata T. Aging Changes of Macromolecular Synthesis in the Avian and Mammalian Eyes as Revealed by Microscopic Radioautography. ARBS Annu Rev Biomed Sci...

متن کامل

Pattern analysis and variations in the utilization of antihypertensive drugs in Taiwan: a six-year study.

BACKGROUND In the last few years there have been changed in the pattern of consumption of antihypertensive drugs in other countries. Factors causing this variability include differences in the effectiveness of detection, guidelines for the management of hypertension, and differences in national health insurance systems among countries. AIM The aim of this study was to reveal patterns in the u...

متن کامل

Roles for learning sciences and learning technologies in biomedical engineering education: a review of recent advances.

Education in biomedical engineering offers a number of challenges to all constituents of the educational process-faculty, students, and employers of graduates. Although biomedical engineering educational systems have been under development for 40 years, interest in and the pace of development of these programs has accelerated in recent years. New advances in the learning sciences have provided ...

متن کامل

Rapid prototyping for biomedical engineering: current capabilities and challenges.

A new set of manufacturing technologies has emerged in the past decades to address market requirements in a customized way and to provide support for research tasks that require prototypes. These new techniques and technologies are usually referred to as rapid prototyping and manufacturing technologies, and they allow prototypes to be produced in a wide range of materials with remarkable precis...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2006