Thermal phase behavior of DMPG: the exclusion of continuous network and dense aggregates.

نویسندگان

  • Juha-Matti I Alakoskela
  • Paavo K J Kinnunen
چکیده

1,2-Dimyristoyl-sn-glycero-3-phospho-rac-glycerol has been suggested to form at intermediate temperatures and at high concentrations in low-salt solutions as a continuous sponge phase (Heimburg, T.; Biltonen, R. L. Biochemistry 1994, 33, 9477-9488). In the present study, the changes in signals seen for a range of fluorescent probes during phase transformations of this phospholipid indicate continuous melting and a change in lipid packing, in accordance with previous reports. However, in accordance with Lamy-Freund and Riske (Lamy-Freund, M. T.; Riske, K. A. Chem. Phys. Lipids 2003, 122, 19-32), no enhancement of lipid mixing within the putative sponge phase region was seen, suggesting a lack of a connected lipid surface. Accordingly, a typical sponge phase cannot account for the properties of the intermediate phase. The low scattering intensities of the latter have also been taken as evidence for disaggregation. While dynamic light scattering and data for membranes containing poly(ethylene glycol)-ylated lipids could lend credence to disaggregation, the most likely explanation for the scattering data would appear to be a shape transition without significant changes in neither vesicle aggregation nor bilayer connectivity. An abrupt change in light scattering and signals from some of the fluorescent probes used reveals a new transition at Tt approximately 43 degrees C, with the formation of a more ordered interface.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

The peculiar thermo-structural behavior of the anionic lipid DMPG.

Aqueous dispersions of the anionic phospholipid dimyristoyl phosphatidylglycerol (DMPG), around 100 mM ionic strength, are known to exhibit a thermal behavior similar to that of the largely studied lipid dimyristoyl phosphatidylcholine (DMPC), which undergoes a gel to liquid crystalline phase transition at 23 degrees C, well characterized by differential scanning calorimetry (DSC), and other me...

متن کامل

DMPG gel-fluid thermal transition monitored by a phospholipid spin labeled at the acyl chain end.

Low ionic strength aqueous dispersion of dimyristoyl phosphatidylglycerol (DMPG) presents a rather peculiar gel-fluid thermal transition behavior. The lipid main phase transition occurs over a large temperature interval (ca. 17 degrees C), along which several calorimetric peaks are observed. Using lipids spin labeled at the acyl chain end, a two-peak electron spin resonance (ESR) spectrum is ob...

متن کامل

Solidification and thermal performance analysis of the low carbon steel during the continuous casting process

The present paper evaluates the effect of the nozzle characteristics on the heat transfer and phase change of the low carbon steel during the continuous casting process. A three-dimensional energy equation and a solidification model are used to drive the governing equation of the phase change and temperature distribution. A linear relation is obtained to predict the temperature-dependent of the...

متن کامل

A Predictive Model Accounting for the Mechanical Behavior of Galvanized Alloy Layers on the Mild Steel

Zinc coating is formed by the heterogeneous assembly of the Γ, Γ1, δ, ζ and η phases whose mechanical properties greatly differ from each other. Thermal strains resulting from large differences between thermal expansion coefficients are partially relaxed by the formation of a crack network. In order to model this phenomenon, initial hardness, thermal expansion coefficient αi and toughness (KIC)...

متن کامل

Thermal Stress Resistance to Fracture and its Relation to with Resistance to Thermal Fatigue and Shock

Dense Silicon nitride was investigated to determine the effect of its microstructural parameters and densification on thermo-mechanical properties and thermal stress resistance to fracture initiation during a hot or cold mechanical and thermal shock testing. The different materials and microstructures were obtained by changing the parameters such as the type of the powder, additive, forming p...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • Langmuir : the ACS journal of surfaces and colloids

دوره 23 8  شماره 

صفحات  -

تاریخ انتشار 2007