Atomistic Study of Surfaces and Interfaces of Fe-Cr and Fe-Cr-Al Alloys

نویسندگان

  • K. Kokko
  • S. Granroth
  • M. H. Heinonen
  • R. E. Perälä
  • T. Kilpi
  • E. Kukk
  • E. Nurmi
  • M. Ropo
  • A. Kuronen
  • L. Vitos
چکیده

Surface and interface properties of Fe-Cr, Fe-Al, and Fe-Cr-Al are studied using Exact Muffin-Tin Orbitals and Monte Carlo methods and with x-ray photoelectron and Auger electron techniques. Surface composition is investigated as a function of oxidation (heating) time. Hard x ray photoelectron spectroscopy (HAXPES) is used to scan non destructively the compositions below the surface. It is found that Cr boosts the Al segregation to the surface. Introduction The fundamental physical difference between Fe and Cr plays a decisive role in the thermodynamics of Fe-Cr based alloys: Cr favours an antiferromagnetic coupling to its neighbours whereas Fe prefers a ferromagnetic one. Small amount of Cr, coupled antiferromagnetically to the host matrix, can be dissolved in Fe. However, with increasing Cr content the average distance between, in this case, ferromagnetically coupled Cr atoms decreases inducing increasing of the CrCr pair energy; the energy of a Cr-Cr dimer in Fe increases 240 meV when Cr atoms are brought from a third-neighbour position to a first-neighbour position [1]. Therefore, with increasing Cr content the energy of the homogeneous Fe-Cr alloy is pushed up inducing: peculiar Fe-Cr mixing enthalpy [2], bulk Cr threshold (≈10 at.% Cr in bulk) for a Cr containing surface [3], and α-α’ phase separation [4]. Chromium in bulk affects also surface properties: within 8–23 at.% Cr in bulk the Cr containing surface has lower surface energy than the pure Fe surface [1] and adding 10 at.% Cr to Fe-Al, the Al concentration can be dropped from ≈15 to ≈3 at.% without weakening the protective alumina surface scale [5,6]. In the present work some effects of substitutional Cr in Fe and Fe-Al are investigated using photoelectron and Auger electron measurements and computer simulations. Materials Science Forum Online: 2013-07-01 ISSN: 1662-9752, Vol. 762, pp 728-733 doi:10.4028/www.scientific.net/MSF.762.728 © 2013 Trans Tech Publications, Switzerland All rights reserved. No part of contents of this paper may be reproduced or transmitted in any form or by any means without the written permission of Trans Tech Publications, www.ttp.net. (#69805089, Pennsylvania State University, University Park, USA-17/09/16,22:38:06)

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

The Effect of Nickel Increasing and Aluminum Addition on Sulfidation Resistance of Fe-Ni-Cr Alloys (TECHNICAL NOTE)

In this research the effects of; increasing the amount of nickel and adding aluminum to create and prolong sulfidation resistance of Fe-Ni-Cr alloys have been investigated. Sulfidation tests were carried out at 1100°C in S/O bearing atmosphere. Prior to the tests, the specimens were annealed in argon at 1250°C for 8 hrs. Weight changes were measured and corroded deposits were analyzed byscannin...

متن کامل

The Effect of the Third Element Cr on Oxidation Behavior of Fe - x Cr - 10 Al ( at . % ) Alloys at 900 o C

Alloys Fe-(0, 5, 10)Cr-10Al (all in at.%) were oxidized at 900 o C in 1 atm oxygen to study the effect of Cr additions on the oxidation behavior. The oxidation kinetics was recorded with a thermal microbalance. The morphologies and microstructures of the oxide scales were examined using SEM, EDS, and XRD. Fe-10Al developed an Al2O3-rich scale during the initial stage of oxidation, and a non-pro...

متن کامل

Effect of surface-applied reactive elements on the early stage oxidation of Fe- 18Cr-5Al and Fe-18Cr-5Al-1Hf alloys

The effect of lanthanum implantation on the early stage oxidation of Fe-18wt%Cr5wt%Al and Fe-l8wt%Cr-5wt%Al-Iwt%Hf alloys at 1100 OC has been investigated. I t was found that the reactive element enriched surfaces oxidized almost two times faster initially, and the scale that formed had a higher iron content. An extremely wavy scale/alloy interface developed in the early stage due to the accele...

متن کامل

Partial phonon densities of states of Fe in Fe-Cr: Analysis by a local-order cluster expansion

Nuclear resonant inelastic x-ray scattering spectra were measured for Fe in disordered body-centered-cubic alloys of Fe-Cr. Partial phonon density of states DOS curves were obtained from these data. These results, in conjunction with the results of Ruckert et al. Hyperfine Interact. 126, 363 2000 on Fe-Cr thin-film multilayers and alloys, were analyzed with a local-order cluster expansion metho...

متن کامل

Joint properties of cast Fe-Pt magnetic alloy laser-welded to Co-Cr alloy.

This study investigated the joint properties of Fe-Pt alloy laser-welded to Co-Cr alloy. Cast plates (0.5 x 3.0 x 10 mm) were prepared with Fe-Pt and Co-Cr alloys. Fe-Pt plates were butted against Co-Cr plates and laser-welded using Nd:YAG laser. Control and homogeneously welded specimens were also prepared. Laser welding was performed with and without argon shielding. Tensile testing was condu...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2016