Comparison of Microleakage and Penetration Depth between Hydrophilic and Hydrophobic Sealants in Primary Second Molar

نویسندگان

  • Pritesh N Gawali
  • Vishwas B Chaugule
  • Amey M Panse
چکیده

INTRODUCTION Optimal pit and fissure sealing is determined by surface preparation techniques and choice of materials. The performance of pit and fissure sealant materials has been intensively investigated, yet no single product is reported as an ideal sealant. In children, moisture control during cavity preparation is always a big challenge, and hence, hydrophilic sealants have been developed. AIM To compare the microleakage and penetration depth of hydrophilic and hydrophobic sealants using acid-etching on dry and moist surfaces. MATERIALS AND METHODS Recently, extracted 28 2nd primary molars are assigned to two groups (hydrophobic group I; hydrophilic group II) depending on the surface condition (dry group: A1 and B1; moist group: A2 and B2) of 7 teeth in each group. Samples from group A1 and B1 are cleaned and dried with a 3-way syringe and etched with etching gel, and sealant is applied to the fissures and cured with visible light. Sample from A2 and B2 are immersed in 0.1 mL of fresh whole human saliva for 20 seconds and dried using a pellet cotton, and the same procedure is carried out. All samples are subjected to 1000 thermal cycles and sectioned to compare the depth of penetration and microleakage. Sections will be examined under light microscope and analyzed using an image analysis software (SigmaScan). RESULTS The least microleakage was seen with hydrophilic sealant under moist surface condition, and the depth of penetration of hydrophobic sealant was found to be better than that of hydrophilic sealant in both dry and moist surface conditions. CONCLUSION Hydrophilic pit and fissure sealants showed higher tolerance to saliva contamination with less microleakage, but in terms of penetration ability hydrophobic sealants were found to be superior. HOW TO CITE THIS ARTICLE Gawali PN, Chaugule VB, Panse AM. Comparison of Microleakage and Penetration Depth between Hydrophilic and Hydrophobic Sealants in Primary Second Molar. Int J Clin Pediatr Dent 2016;9(4):291-295.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Comparison of Microleakage of Self-etch and Total-etch Bonding Agents in Primary Molar Class II Composite Restorations

Introduction: This study evaluated microleakage of flowable and conventional composite in primary molar class II restorations using self-etch and total-etch bonding agents. Methods: Class II standard cavities were prepared on proximal surface of 48 primary molars. These cavities were restored using GrandioFlow and Grandio composites and Futurabond DC and Solobo...

متن کامل

A comparison of microleakage between two retrograde filling materials (MTA and Amalgam) using dye leakage method

A comparison of microleakage between two retrograde filling materials (MTA and Amalgam) using dye leakage method Dr. M. Tabrizizadeh* - Dr. K. Rostam Yazdi** *- Assistant Professor of Endodontics Dept. – Faculty of Dentistry – Yazd University of Medical Sciences. **- Dentist. Background and Aim: There is a need for a material with high sealing ability to prevent bacterial and tissue secretions ...

متن کامل

Effects of fissure cleaning methods, drying agents, and fissure morphology on microleakage and penetration ability of sealants in vitro.

PURPOSE The purpose of this in vitro study was to determine the effect of different cleaning methods and the use of post-etching drying agents, as well as the influence of fissure types on the microleakage and penetration ability of fissure sealants. METHODS Ninety extracted human molar teeth were randomly divided into 9 groups of 10 each. The treatment groups were defined by the combination ...

متن کامل

In Vitro Comparison of Microleakage of Two Nanohybrid Flowable Composites and RMGI in Class V Restorations in Primary Molars

Introduction: Composite resins undergo microleakage due to polymerization shrinkage particularly when located in enamel free margins. The purpose of this study was to assess and compare the  microleakage of two nanohybrid  flowable composites and resin modified glass ionomer in class V restorations of primary mandibular second  molars.  Materials and Methods: This in vitro, experimental study ...

متن کامل

Microleakage and penetration ability of resin sealant versus bonding system when applied following contamination.

PURPOSE The purpose of this study was to evaluate the microleakage and penetration ability of sealing materials applied under different conditions of contamination. METHODS One hundred twenty extracted human molar teeth were randomly assigned to 12 groups. The treatment groups were defined by the combination of sealing materials (Concise; Optibond system; Optibond system plus Concise) and 4 s...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره 9  شماره 

صفحات  -

تاریخ انتشار 2016