Effect of Different Solutions on Knoop Hardness of Indirect Composite Resins

نویسنده

  • dos Santos
چکیده

Introduction: Indirect dental composites may have adequate clinical performance. However, the literature is scarce regarding indirect composite resins and these solutions should be considered to maintain their properties. The aim of the study was to evaluate the influence of beverages, mouthwashes and bleaching agents on the hardness of indirect composite resins. Methods: Five different brands of indirect composite resins were evaluated: Adoro, Resilab, Cristobal, Sinfony and Epricord. Ten specimens of each brand were immersed in eleven different solutions: four mouthwashes (Listerine, Oral-B, Plax, Periogard), four beverages (coke soft drink, red wine, coffee, orange juice), three dental bleaching agents (16% peroxide of carbamide, 7.5% and 38% peroxide of hydrogen) and artificial saliva (control group). The Knoop hardness was measured before (baseline) and after 12, 24, 36 and 60 hours of immersion in mouthwashes; after 7, 14 and 21 days of immersion in beverages and after 7 and 14 days of immersion in dental bleaching agents. The results were analyzed using 3-way repeated measures ANOVA and Tukey’s test (p<0.05). Results: All resins presented significant decrease on hardness values after immersion process whereas this reduction was higher for Resilab and Sinfony. The latter exhibited the lowest initial values of hardness while Cristobol resin presented the highest hardness values. The mouthwashes promoted a significant decrease in the hardness of specimens. *Corresponding author: Daniela Micheline dos Santos, Araçatuba Dental School, Univ Estadual Paulista – UNESP, Department of Dental Materials and Prosthodontics, Street: José Bonifácio, 1193 – Vila Mendonça, CEP 16015050 Araçatuba, São Paulo, Brazil, Tel: 55-18-3636-3287; Fax: 55-18-36363245; E-mail: [email protected] Received January 03, 2014; Accepted February 03, 2014; Published February 05, 2014 Citation: dos Santos DM, Massurani L, Goiato MC, Zavanelli AC, Haddad MF, et al. (2014) Effect of Different Solutions on Knoop Hardness of Indirect Composite Resins. Dentistry 4: 208. doi:10.4172/2161-1122.1000208 Copyright: © 2014 dos Santos DM, et al. This is an open-access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Effect of the increase of energy density on Knoop hardness of dental composites light-cured by conventional QTH, LED and xenon plasma arc.

The aim of this study was to evaluate the effect of the increase of energy density on Knoop hardness of Z250 and Esthet-X composite resins. Cylindrical cavities (3 mm in diameter X 3 mm in depth) were prepared on the buccal surface of 144 bovine incisors. The composite resins were bulk-inserted and polymerized using different light-curing units and times: conventional QTH (quartz-tungsten-halog...

متن کامل

[Microhardness of resins as a function of color and halogen light].

The aim of this study was to evaluate the influence of light intensity and the influence of the color of a composite resin on Knoop hardness. Samples were confected utilizing polyester matrices with 6 mm of diameter and 2 mm of depth. The matrices were filled with composite resin (Fill Magic - Vigodent), colors A3, B3, C3, D3 and I, and light-cured by means of an Elipar light-curing unit in thr...

متن کامل

Comparison of silorane and methacrylate-based composite resins on the curing light transmission.

The aim of this study was to investigate the influence of different composite resins - Filtek P90 (silorane-based composite) and Heliomolar (methacrylate-based composite) - on light transmission and decrease in Knoop hardness between the bottom and top of cured specimens. The irradiance of a light-curing unit (LCU) was measured with a power meter (Ophir Optronics; 900 mw/cm2) and spectral distr...

متن کامل

Microhardness of dual-polymerizing resin cements and foundation composite resins for luting fiber-reinforced posts.

STATEMENT OF PROBLEM The optimal luting material for fiber-reinforced posts to ensure the longevity of foundation restorations remains undetermined. PURPOSE The purpose of this study was to evaluate the suitability of 3 dual-polymerizing resin cements and 2 dual-polymerizing foundation composite resins for luting fiber-reinforced posts by assessing their Knoop hardness number. MATERIAL AND ...

متن کامل

Impact of refrigeration on the surface hardness of hybrid and microfilled composite resins.

This in vitro study evaluated the Knoop hardness of the composite resins Charisma (C) and Durafill VS (D) polymerized in 3 different conditions: at room temperature (A) (23 +/- 1 degrees C); refrigerated at 4 +/- 1 degrees C and immediately photo-activated after removal from the refrigerator (0); and, refrigerated at 4 +/- 1 degrees C and photo-activated after a bench time of 15 min at room tem...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2014