Dilatometric and Hardness Analysis of C45 Steel Tempering with Different Heating-up Rates

نویسنده

  • A. KULAWIK
چکیده

Modelling of technological processes of heat treatment or welding, involving multiple heat source transitions, requires considering the phenomenon of tempering. In work have been presented results of dilatometric research of hardened C45 steel subjected to tempering. The analysis of the infl uence of heating rate at the kinetic determined from dilatometric curves has been made. There have also been estimated quantities of transformation expansions and thermal expansion coeffi cients of hardening and tempering structures (austenite, ferrite, pearlite, martensite and sorbite). The analysis of tempering time infl uence on the hardness of tempered steel has been made. Functions associating hardness with tempering time (rate of heating-up) in technological processes based on short-timed action of a heat source (eg. laser treatment) have been suggested.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

THE KINETIC OF PRECIPITATION REACTIONS IN A RAPIDLY AGED HIGH ALLOY HIGH STRENGTH STEEL

This study was launched to investigate the effects of heating rate and aging parameters on the kinetic of precipitation reactions in a high alloy high strength steel having Ni, Co, Mo and Ti. For this purpose, as quenched specimens were subjected to three types of aging methods with different heating rates. These methods consisted of aging in Pb bath, salt bath, and furnace at different aging c...

متن کامل

Experimental Investigations on Heat Treatment of Cold Work Tool Steels: Part 1, Air-hardening Grade (d2)

The present experimental investigations deal with the improvement of mechanical properties of cold work tool steels through different heat treatment processes. An attempt was made to get optimal combination of hardness and toughness through changes of microstructure by heat treatment. The toughness of D2 tool steel increases with tempering temperature. The hardness of D2 tool steel decreases wi...

متن کامل

Effect of Heat Treatment Process on the Fatigue Behavior of AISI 1060 Steel

This experimental study investigated the effects of quenching and tempering heat treatment on fatigue behavior and also tempering temperature and time holding of AISI 1060 steel. At first, the specimens were austenitized at 800˚C for 1 hour, and then were quenched in the water bath of 25˚C temperature. After that, tempering process was done at the temperature of 250˚C, 450˚C and 650˚C for 1 and...

متن کامل

Laser clading of Inconel 625 on ASTM A575 steel

In this research, the microstructure of Inconel 625 cladded layer on ASTM A575 steel has been investigated. By examining different parameters, the optimal single-pass sample with the least amount of dilution, porosity and fusion and suitable wetting angle was determined. Then cladding process with the optimal parameter was performed. The microstructure of the cladding layer was evaluated from t...

متن کامل

Effect of Tempering Temperature on the Microstructure and Hardness of a Super-bainitic Steel Containing Co and Al

The effect of tempering temperature, within the range of 400 to 700°C, on the microstructure and hardness of two super-bainitic steels, one as the control parent sample and the other with added Co & Al was investigated. Post-tempering examinations of the super-bainitic samples showed that low temperature tempering cycles (400–500°C) resulted in carbides formation, and some increases in the hard...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2011