Effect of Asperity Interacting Frequency on Rolling contact Fatigue : 2nd Report, The Cases of a Thermal Refined S45C Carbon Steel, a Hardened SCM435 Alloy Steel and a Case-Hardened SCM415 Alloy Steel
نویسندگان
چکیده
منابع مشابه
Finite Element Analysis of Hardened Steel Cutting
Hard machining, as attractive replacement for many rough and finish grinding operation, generates high cutting forces and temperature that enhance tool wear when act together. Therefore, the tool geometry and machining parameters have to be carefully optimized for a given material. Because of high cost and time consuming experimental work up-to-date advanced software for modeling and simulation...
متن کاملthe effect of consciousness raising (c-r) on the reduction of translational errors: a case study
در دوره های آموزش ترجمه استادان بیشتر سعی دارند دانشجویان را با انواع متون آشنا سازند، درحالی که کمتر به خطاهای مکرر آنان در متن ترجمه شده می پردازند. اهمیت تحقیق حاضر مبنی بر ارتکاب مکرر خطاهای ترجمانی حتی بعد از گذراندن دوره های تخصصی ترجمه از سوی دانشجویان است. هدف از آن تاکید بر خطاهای رایج میان دانشجویان مترجمی و کاهش این خطاها با افزایش آگاهی و هوشیاری دانشجویان از بروز آنها است.از آنجا ک...
15 صفحه اولCopper Precipitation Hardened, High Strength, Weldable Steel
Steel containing 0.03% carbon, 1.35% copper and 0.84% nickel had yield strength in the 540-625 MPa (78-90 Ksi) range depending on thickness, ultimate tensile strength in the 625-690 MPa (90100 Ksi) range, and 25-30% elongation when air cooled after hot rolling. No brittle heat-affected zone was formed during manual or automatic submerged arc welding without pre-heating or postheating. The fract...
متن کاملThe Effect of Pre-strain on Fatigue for a High Strength Low Alloy (hsla)steel
D. Aguirre-Guerrero, A. Juárez-Hernández, M.A.L. Hernández-Rodríguez, University Autonumous of Nuevo León, Faculty of Mechanical and Electrical Engineering, Nuevo León, México. R. Morales, I. Ruiz, PEMSA Co. Celaya, Guanajuato, México. The eff ect of initial plastic strain c ycle fatigue lives of HSLA specimens is in vestigated. Specimens were monotonically, quasi-statically loaded under strain...
متن کاملOn machining of hardened AISI D2 steel with PCBN tools
This paper describes an experimental investigation on machining of a difficult-to-cut material, AISI D2 steel of hardness 62 HRC with PCBN tools. It was found that the most feasible feeds and speeds fall in the ranges 0.08–0.20 mm/rev and 70–120 m/min, respectively and that most of the tested PCBN tools reached the end of life mainly due to flank wear. The highest acceptable values of tool life...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ژورنال
عنوان ژورنال: Bulletin of JSME
سال: 1986
ISSN: 0021-3764,1881-1426
DOI: 10.1299/jsme1958.29.3560