Experimental investigations of heat transfer coefficient of CuO/Water nanofluid are reported in this paper. The heat transfer coefficient of the CuO/water was measured with the help of double pipe heat exchanger. The nanofluid was prepared by dispersing a CuOnano particle in deionized water. CuO/water nanofluid with a nominal diameter of 27nm at different volume concentrations (0.1 &0.3 vol.%) ...

In this study the performances of various non-circular microchannel heat sinks (normalized with circular shape) have been comparatively analyzed for CuO-water nanofluid and baseline pure water flow. Nusselt number and Poiseuille number for each microchannel and thermo-physical properties of CuO-water nanofluid (viz., thermal conductivity, viscosity, specific heat and density) have been designed...

In this study, enhancements of thermal conductivities of ethylene glycol, water, and synthetic engine oil in the presence of copper (Cu), copper oxide (CuO), and multi-walled carbon nanotube (MWNT) are investigated using both physical mixing method (two-step method) and chemical reduction method (one-step method). The chemical reduction method is, however, used only for nanofluid containing Cu ...

This paper presents results of investigations on the application of CuO-water nanofluids for intensification of convective heat transfer. Performance of nanofluids with 2.2 and 4.0 vol.% CuO NPs (nanoparticles) content were examined with regard to heat transfer coefficient and pressure losses in case of turbulent flow in a tube. Negligible impact of examined nanofluid on heat transfer improveme...

Convective heat transfer can be enhanced by changing flow geometry and/or by enhancing thermal conductivity of the fluid. This study proposes simultaneous passive heat transfer enhancement by combining the geometry effect utilizing nanofluids inflow in coils. The two nanofluid suspensions examined in this study are: water-Al2O3 and water-CuO. The flow behavior and heat transfer performance of t...

This study numerically investigates heat transfer augmentation using water-based Al₂O₃ and CuO nanofluids flowing in a triangular cross-sectional duct under constant heat flux in laminar flow conditions. The Al₂O₃/water nanofluids with different volume fractions (0.1%, 0.5%, 1%, 1.5%, and 2%) and CuO/water nanofluids with various volume fractions (0.05%, 0.16%, 0.36%, 0.5%, and 0.8%) are employ...

In the present paper, the effect of water-CuO nanofluid on the radiator heat transfer of an automobile, Peugeot 405 XU7 engine type is investigated experimentally. The experiments are carried out for the radiator water (water-ethylene glycol with a volume fraction of 80-20, respectively) as a base fluid and water-CuO nanofluid with the volume fraction of 0.5% and 1%. Sodium Dodecyl Sulfate (SDS...

Dynamic viscosity values for three particular water-based nanofluids have been experimental determined using a commercial ‘piston-type’ viscometer. Viscosity data, expressed as a function of temperature and particle volume fraction, are presented for 29nm particle-size CuO-water and Al2O3-water with 36nm and 47nm particle-sizes, temperatures up to 75°C and particle volume fraction up to 9%. In ...

The entropy generation based on the second law of thermodynamics is investigated for turbulent forced convection flow of ZrO2-water nanofluid through a square pipe with constant wall heat flux. Effects of different particle concentrations, inlet conditions and particle sizes on entropy generation of ZrO2-water nanofluid are studied. Contributions from frictional and thermal entropy generations ...

Numerical investigation has been carried out on heat transfer and friction factor characteristics of copper-water nanofluid flow in a constant heat-fluxed tube with the existence of new configuration of vortex generator using Computational Fluid Dynamics (CFD) simulation. Two types of swirl flow generator: Classical twisted tape (CTT) and Parabolic-cut twisted tape (PCT) with a different twist ...