نتایج جستجو برای: Dissimilar metals welding

تعداد نتایج: 87633  

2004
Keiji Iwasaki Shoji Ohkawa Motohiro Uo Tsukasa Akasaka Fumio Watari

The performance of laser welding of Ti and two dental precious alloys (Ag-Pd-Au, Au-Pt-Ag) was investigated by mechanical testing and microscopic observation, using butt joint as design. The laser irradiation was done using a commercial Nd:YAG dental laser-welding device in a single pulse mode with output currents 150, 200, 250, 300A, spot diameters 0.6, 0.9, 1.2mm, and pulse duration 10ms. The...

2015
E. M. Anawa

The dissimilar joint between aluminum/titanium alloys (Al 6082 and Ti G2) were successfully achieved by CO2 laser welding with a single pass and without filler material using the overlap joint design. Laser welding parameters ranges combinations were experimentally determined using Taguchi approach with the objective of producing welded joint with acceptable welding profile and high quality of ...

2015
K. Kalaiselvan A. Elango

Laser beam welding of dissimilar sheet metal combinations such as Ti/Al, SS/Al and Cu/Al are increasingly demanded due to high energy densities with less fusion and heat affected zones. A good weld joint strength involves combinations of dissimilar metals and the formation of solid solution in the weld pool. Many metal pairs suffer from significant intermetallic phase formation during welding w...

2012
A. Pradeep

–Friction stir welding is a solid state welding technology used for welding low melting point metals, such as Al, Mg and its alloys. Later welding was conducted on dissimilar metals which also produced a better defect free joint. Tool design and welding parameters contributes a major role for producing a better weld. Material flow and friction heat are the factors that the internal factor for t...

2013
E. M. Anawa A. G. Olabi

The most common problem of welding dissimilar metals (DMWs) with respect to residual stresses is the differences in the coefficient of thermal expansion and heat conductivity of the two welded metals. In the present work, a CO2 continuous laser welding process was successfully applied and optimized for joining a dissimilar AISI 316 stainless steel and low carbon steel plates. The Taguchi approa...

2014
B. R. Moharana S. K. Sahoo

Laser welding is an advance non-traditional and high energy beam welding technique for dissimilar material, which is being increasingly used in industries like automobile, nuclear reactors, aerospace etc. Again it is a very tough task to joining dissimilar materials due to their properties variation. In this present work two dissimilar metals such as copper and AISI 304 stainless steel are take...

Journal: :Applied optics 2014
Huan Huang Lih-Mei Yang Shuang Bai Jian Liu

In this paper, welding of dissimilar metals was demonstrated for the first time, to the best of our knowledge, by using a high-energy high-repetition-rate femtosecond fiber laser. Metallurgical and mechanical properties were investigated and analyzed under various processing parameters (pulse energy, repetition rate, and welding speed). Results showed that the formation of intermetallic brittle...

Journal: :journal of advanced materials and processing 0
khalil gheisari department of materials science and engineering, faculty of engineering, shahid chamran university, ahvaz, iran mohammad reza abasi department of materials science and engineering, faculty of engineering, shahid chamran university of ahvaz, ahvaz, iran

dissimilar metals friction welding of austenitic–martensitic stainless steels is commonly used in order to manufacture engine valves in the automobile industry. in this study, x53crmnnin219 (austenitic stainless steel) and x45crsi93 (martensitic stainless steel) valve steel rods were welded by friction welding process. the welded joint was then heat treated at 760 0c for 60 min. mechanical prop...

Journal: :Journal of Physics: Conference Series 2017

2012
Shubhavardhan RN

The purpose of this work was to join and assess the development of solid state joints of dissimilar material AA6082 aluminum alloy and AISI 304 stainless steel, via continuous drive friction welding process, which combines the heat generated from friction between two surfaces and plastic deformation. Tests were conducted with different welding process parameters. The results were analyzed by me...

نمودار تعداد نتایج جستجو در هر سال

با کلیک روی نمودار نتایج را به سال انتشار فیلتر کنید