Electrochemical characteristic parameters such as diffusional permeability, ion transport number, fi xed charge concentration and electrical resistance for a regenerated cellulose/polypropylene-supported membrane (RC/PP sample) in contact with NaCl solutions at different concentrations were determined. The effect of the polypropylene support on mass and charge transport was estimated by compari...

Graft polymerization of acrylic acid onto nonwoven polypropylene (PP) fabric was carried out by a preirradiation method using a Co gamma radiation source. Results showed that 2.2'-Azobisisobutyronitrile (AIBN), its concentration was 0.2%, was very important during the grafting polymerization without removal of polymerization inhibitor of AA. The most favorable grafting polymerization conditions...

TiO(2) porous nanospheres on polypropylene (PP) films (TiO(2)/PP composite) are produced at ambient temperature. Particle/pore size match up is the key anchoring point to overcome the low affinity between hydrophilic materials and hydrophobic materials. With the hydrophilic TiO(2) catalyst evenly dispersed on a hydrophobic surface, the aqueous solution will selectively skip the substrate and we...

N6) made with or without PP-g-MAH as compatibilizer are investigated. The blend filaments produced at the take-up speeds of 300 and 800 m/min were drawn with draw ratio of 3.5 and 2, respectively. Effects of blending of N6 with PP on birefringence , crystalline, and amorphous orientation factors of the composite filaments are studied. The amorphous orientation factor, fam of PP was found to inc...

Abstract This study describes the development of a fog collector material for harvesting. Polypropylene (PP) doped with fumed silica (0–2%) was punctured at equal intervals and exposed to produced by humidifier. The amount water harvested each sample measured using an ultrasonic fogger. 1% most effective harvesting water, collected almost 19–20 times more than pure polypropylene. improvement is...

The compatibilities of polymer blends, Polypropylene(PP) and Polyamide12(PA12), was simulated by molecular dynamics(MD) simulations. Density, cohesive energy density (CED) ,and solubility parameters(δ) of pure substances and PP/PA12 blends were calculated by MD simulations with the COMPASS force field for the prediction of polymer blends compatibility . Results showed that PP/PA12 is not miscri...

Polypropylene (PP) exhibits excellent insulation properties, high thermo-stability, and recyclable nature, thus expected to be the next-generation material for HV cable application. Chemical grafting modification is an effective technology improve electrical properties of polypropylene. In this paper, we develop report a new-type grafted PP by water-phase technology. The comprehensive including...

In this study, we develop binary polypropylene (PP) composites with hexagonal boron nitride (hBN) nanoplatelets and ternary hybrids reinforced with hBN and nanohydroxyapatite (nHA). Filler hybridization is a sound approach to make novel nanocomposites with useful biological and mechanical properties. Tensile test, osteoblastic cell culture and dimethyl thiazolyl diphenyl tetrazolium (MTT) assay...

Melt flow and dripping of the pyrolysing polymer melt can be both a benefit and a detriment during a fire. In several small-scale fire tests addressing the ignition of a defined specimen with a small ignition source, well-adjusted melt flow and dripping are usually beneficial to pass the test. The presence of flame retardants often changes the melt viscosity crucially. The influence of certain ...

table grapes (vitis vinifera l. cv. shahroodi) were stored for 45 days under modified atmospher packaging (map) with four gas combination treatments including gc1 (control or air), gc2 (10%co2+5%o2), gc3 (10%co2+15%o2) and gc4 (10%co2 + 60%o2) using two types of polymeric films pp (polypropylene) and pe (polyethylene) at 1oc and 80-90% rh. measurements were carried out after each 15 days at 1oc...