In the present work the effects of plasma nitridization on the passivation behavior of AISI 316L was investigated. To do this; nitriding treatments were carried out at 420°C for 1, 2, 4 and 16 hours. The phase composition and structure of the nitrided layer were studied by Low Angle X-ray diffraction and Scanning Electron Microscopy. The hardness of samples also was evaluated by Vickers microha...

Intergranular stress corrosion cracking has occurred in BWR environments in non-sensitised, cold-worked austenitic stainless steel materials. The affecting parameters are so far not fully known, but deformation mechanisms may be decisive. The effect of cold deformation and nitrogen content on the deformation behaviour of austenitic stainless steels was investigated. The materials were austeniti...

The goal of this project was to develop low-firing thick-film materials systems for the fabrication of piezoresistive sensors on special steels, for the fabrication of instrumented medical devices. To this end, a series of individual thick-film materials and complete systems, based on lead borosilicate glasses, were developed and extensively characterised. These studies allowed us to formulate ...

In this work, changes undergone at the passive layer of a new type of corrugated austenitic stainless steel (low Ni, high Mn 204Cu type) when exposed to solutions simulating that contained in the pores of concrete have been studied. Changes in the nature of the passive layer have been characterized by X-ray photoelectronic spectroscopy (XPS) and electrochemical impedance spectroscopy (EIS). Par...

The monotonic and cyclic deformation behavior of ultrafine-grained metastable austenitic steel AISI 304L, produced by severe plastic deformation, was investigated. Under monotonic loading, the martensitic phase transformation in the ultrafine-grained state is strongly favored. Under cyclic loading, the martensitic transformation behavior is similar to the coarse-grained condition, but the cycli...

Austenitic stainless steels offer good property combinations for structural component applications in demanding and aggressive environments, including nuclear power plants, where irradiation assisted degradation failures have been reported [1]. Enhanced irradiation tolerance has been reported for materials containing a high density of internal interfaces that act as point defect annihilation or...

*Correspondence: Tadeusz Hryniewicz and Krzysztof Rokosz, Division of Surface Electrochemistry, Koszalin University of Technology, Raclawicka 15-17, Koszalin PL 75-620, Poland e-mail: tadeusz.hryniewicz@ tu.koszalin.pl; [email protected] The research work has been concerned on the studies and development of electrochemical polishing in the magnetic field magnetoelectropolishing (MEP) in com...

Microstructural evolutions during annealing of cold rolled AISI 304L and AISI 316L stainless steels were studied. Cold rolled AISI 304L alloy was fully martensitic but cold rolled AISI 316L alloy was partially martensitic due to the higher stability of the austenite phase in the latter. During continuous heating to elevated temperatures, the complete reversion of strain-induced martensite at 75...

Abstract The corrosion polarization behavior of 439ll ferritic (439ll), 316L austenitic (316L), and NO7208 nickel-chromium-aluminum-iron (NO7208) stainless steels, Ti6Al4V titanium (Ti6Al4V) alloys was studied in 4 M H 2 SO + 5% NaCl solution at 35 70°C. Corrosion rate ( C R ) the were generally higher alloy exhibited resistance to general 35°C (0.067 0.050 mm/year) while most reactive (0.506 m...

Complex two-component peak of anelastic mechanical losses was observed in multicomponent substitutional austenitic alloys after prior plastic deformation. In AISI 316L, AISI 316LN, AISI 310 and AISI 304 austenitic stainless steels, this peak is situated in the wide range of temperature from 200 to 400K. Characteristics of the observed peak for different thermo-mechanical treatments were studied...