Fe-substituted MCM-41 molecular sieves with ca. 1, 2, and 3 wt % Fe were synthesized hydrothermally using different sources of colloidal silica (HiSil and Cab-O-Sil) and characterized by ICP, XRD, N2 physisorption, UV-vis, EPR, TPR, and X-ray absorption. Catalysts synthesized from Cab-O-Sil showed higher structural order and stability than those from HiSil. The local environment of Fe in the me...

Sensors that detect directly and in situ the status of automotive exhaust gas catalysts by monitoring the electrical properties of the catalyst coating itself are overviewed. Examples included in this review are the in-situ determination of the electrical impedance of three-way catalysts based on ceria-zirconia solutions and of lean NO(x) traps of earth-alkaline based coatings, as well as appro...

The Zeolite Y as a support was modified by the incorporating of Fe and TiO2 in one single step using impregnation method. The synergistic effects between those components enhance the catalytic activity for the degradation of amaranth dye under ultrasonic irradiation with output power of 50 W and 40 kHz frequency. Different characterization techniques were used to elucidate the physical and chem...

Iron aminoantipyrine (Fe-AAPyr), graphene nanosheets (GNSs) derived catalysts and their physical mixture Fe-AAPyr-GNS were synthesized and investigated as cathode catalysts for oxygen reduction reaction (ORR) with the activated carbon (AC) as a baseline. Fe-AAPyr catalyst was prepared by Sacrificial Support Method (SSM) with silica as a template and aminoantipyrine (AAPyr) as the organic precur...

A parametric study of carbon nanotube (CNT) synthesis from catalytically active porous anodic Al–Fe–Al multilayer templates was conducted with respect to pore aspect ratio, Fe layer thickness, CNT synthesis temperature, and pre-anodization thermal annealing. Performance metrics included CNT catalytic activity and the pore wall integrity at the Al–Fe–Al interface. The observed CNT density was a ...

PtRu catalyst is a promising anodic catalyst for direct methanol fuel cells (DMFCs) but the slow reaction kinetics reduce the performance of DMFCs. Therefore, this study attempts to improve the performance of PtRu catalysts by adding nickel (Ni) and iron (Fe). Multiwalled carbon nanotubes (MWCNTs) are used to increase the active area of the catalyst and to improve the catalyst performance. Elec...

Efficient and environmentally friendly syntheses of xanthenes derivatives by using γ-Fe2O3@HAP-Fe2+ NPs as a catalyst has been carried out. The catalyst can be readily isolated by using an external magnet and no obvious loss of activity was observed when the catalyst was reused in eight consecutive runs. The procedure has several advantages, such as economic...

Iron catalysts have been used widely for the mass production of carbon nanotubes (CNTs) with high yield. In this study, UV/visible spectroscopy was used to determine the Fe catalyst content in CNTs using a colorimetric technique. Fe ions in solution form red-orange complexes with 1,10-phenanthroline, producing an absorption peak at λ=510 nm, the intensity of which is proportional to the solutio...

In this study, β-cyclodextrin(β-CD) supported, hydroxyapatite encapsulated γ-Fe2O3 (γ-Fe2O3@HAp@β-CD) was successfully prepared and evaluated as a solid-liquid phase transfer catalyst and also a molecular host system and nanoreactor for the nucleophilic ring-opening of epoxides in water for the preparation of β-azido alcohols, β-nitro alcohols, an...

We report the controlled growth of ultralong single-wall carbon nanotube (SWNT) arrays using an improved chemical vapor deposition strategy. Using ethanol or methane as the feed gas, monodispersed Fe-Mo as the catalyst, and a superaligned carbon nanotube (CNT) film as the catalyst supporting frame, ultralong CNTs over 18.5 cm long were grown on Si substrates. The growth rate of the CNTs was mor...