In this research, comparative study of corrosion resistance of aluminum based alloys and Al-alloys with nickel have been investigated. Several processes are conducted for the AlZn-Mg-Cu alloys and Al-Zn-Mg-Cu-0.5%Ni alloys were homogenized, aged then retrogressed and reaged; also, alloys were homogenized then the extruded thereafter heat treated. Al-Zn-Mg-Cu alloy and AlZn-Mg-Cu-Ni alloy sample...

The sensitization and subsequent intergranular corrosion of Al-5.3 wt.% Mg alloy has been shown to be an important factor in stress corrosion cracking of Al-Mg alloys. Understanding sensitization requires the review of grain boundary character on the precipitation process which can assist in developing and designing alloys with improved corrosion resistance. This study shows that the degree of ...

High strength, wrought 7xxx (Al-Zn-Mg) and Al-Li based alloys show a propensity for fatigue macroscopic crack deflections aligned along grain boundaries. The present work reports a study on a 3 rd generation Al-Li based alloy in the form of a thick AA2297 (Al-Cu-Li alloy) plate, where it was found that although the lithium containing material may indeed be more susceptible to mixed mode grain b...

The effects of adding 0.02 or 0.06 at.% Si to Al–0.06Sc–0.06Zr (at.%) are studied to determine the impact of Si on accelerating Al3(Sc,Zr) precipitation kinetics in dilute Al–Sc-based alloys. Precipitation in the 0.06 at.% Si alloy, measured by microhardness and atom-probe tomography (APT), is accelerated for aging times <4 h at 275 and 300 C, compared with the 0.02 at.% Si alloy. Experimental ...

in the present study, mechanical properties and low cycle fatigue behavior of a solid-solutionized aa6061 aluminum alloy produced by equal channel angular pressing (ecap) process were investigated. the grain refinement after two passes of ecap significantly increased the yield stress and ultimate tensile stress and decreased the ductility of the alloy. however, the improvement of low cycle fati...

Recycling of aluminum alloys often decrease fluidity, consequently influence the castability of the alloy. In this study, the fluidity of Al-Zn alloys, such as the standard A713 alloy with and without scrap addition has been investigated. The scrap added was comprised of contaminated alloy turning chips. Fluidity measurements were performed with double spiral fluidity test consisting of gravity...

The microstructure, tensile, and creep behavior of a Ti-5Al-45Nb (at. pct) alloy was evaluated. The main objective of processing and characterizing this alloy was to obtain the constituent properties of a fully-b Ti-Al-Nb alloy to aid in modeling the tensile and creep properties of twophase orthorhombic + body-centered-cubic (O + bcc) alloys. A second objective was to compare the tensile and cr...

In the present study, an attempt has been made to investigate the influence of the forging parameters on cutting forces for different cutting speed, depth of cut, and feed rate during machining of Al 7075 alloy and Al 7075 alloy with short basalt fiber reinforced metal matrix composites. The experiments were conducted by using a lathe machine with tool dynamometer setup. KeywordForging effect, ...

It was recently shown that silicon particles in heat-treated Al–Si casting alloys can contain flaws such as surface pinholes and grooves, which cause varying degrees of reduction in the in situ particle fracture strength and hence influence the mechanical properties of this class of alloys. In this work, we show that the formation of one class of such strength-limiting flaws in solidified and c...

In this study, Al2014 alloy refined with Al-5%Ti-1%B master alloy was prepared by strain-induced melt activated (SIMA) process. The main variables of the SIMA process were cold working, holding time and temperature in semi-solid state. Cold working was applied on specimens by upsetting technique to achieve 10%, 20% and 30% height reduction. Cold worked specimens were heat treated in semi-s...