نتایج جستجو برای: flexural properties

تعداد نتایج: 875188  

ABU FANAS S.H., , HADIAN A.M., ,

Enhancing the properties of dental resin composites is of interest to researchers. The objective of the present investigation was to improve the strength and fracture toughness of dental composites via addition of silicon carbide whiskers and substitution of commonly used filler materials with stabilized zirconia ceramic powder. It was also intended to study the effect of powder- to- whisker ra...

This article reports the effective usage of redmud(RM) an industrial waste ,as a  novel filler in polymer matrix. The composite has been fabricated with redmud as secondary reinforcement in banana fiber reinforced polyester (BFRP) using compression molding technique. The mechanical properties such as tensile, flexural and impact strength have been studied for different fiber weight percentage, ...

Journal: :journal of dental biomaterials 0
na. taha department of conservative dentistry, jordan university of science and technology, irbid, jordan a. ghanim oral health cooperative research centre, melbourne dental school, the university of melbourne, australia ms. tavangar department of dental materials, school of dentistry, shiraz university of medical sciences, shiraz, iran

statement of problem: there are controversial reports regarding physical and mechanical properties of resin composites and glass ionomer cements. some revealed higher strength and hardness for resin composites while others showed a comparable value for glass ionomer cements. evaluation of mechanical properties of different types of resin composites in comparison with resin modified glass ionome...

2013

Experimental study on the influence of fibre content on crack behaviour and propagation in synthetic-fibre reinforced beams has been reported in this paper. The tensile behaviour of metallic fibre concrete is evaluated in terms of residual flexural tensile strength values determined from the load-crack mouth opening displacement curve or load-deflection curve obtained by applying a centre-point...

Journal: :int. j. lignocellulosic products 2014
m. mehdinia a. a. enayati m. layeghi

the use of agriculture residues as filler in composites is increasing due to their strength, abundance and low cost. soya stalks show promising renewable natural fiber. in polyethylene composites the physical and mechanical properties (flexural resistance, tensile, impacted absorbed energy, water uptake and thickness swelling) was examined at different composites. the results showed that, the m...

2011
M. ASHOK KUMAR RAMACHANDRA REDDY

Aim of this work was to investigate the tensile, flexural and dielectric properties of composites made by reinforcing Sansevieria cylindrica as a new natural fibre into a rubber based polyester matrix. The fibres extracted by retting and manual processes were used to fabricate the composites. These composites were tested for the properties which mentioned above and compared with those of establ...

Journal: :Journal of oral rehabilitation 2005
N Yunus A A Rashid L L Azmi M I Abu-Hassan

Nylon denture base material could be a useful alternative to poly (methyl methacrylate) (PMMA) in special circumstances such as patient allergy to the monomer. The aim of this study was to evaluate the flexural properties of a nylon denture base material (Lucitone FRS), a conventional compression-moulded heat-polymerized (Meliodent), a compression-moulded microwave-polymerized (Acron MC) and an...

2015
Yangyang Chen Jin Hu Guoliang Huang

The ability to control flexural wave propagation is of fundamental interest in many areas of structural engineering and physics. Metamaterials have shown a great potential in subwavelength wave propagation control due to their inherent local resonance mechanism. In this study, we propose a transformation method to derive the material properties of a flexural waveguide and implement the function...

Journal: :Dental materials journal 2008
Masao Irie Rosalina Tjandrawinata Lihua E Takashi Yamashiro Suzuki Kazuomi

The purpose of this study was to evaluate the flexural strength, flexural modulus, modulus of resilience, and water sorption of four flowable light-cured composite resins (FCRs). Results were then compared with four conventional composite resins (CCRs) and a minifilled hybrid light-cured composite resin, which served as a control. Twenty specimens were flexural tested immediately after curing, ...

Journal: :The Journal of experimental biology 2003
S A Combes T L Daniel

The dynamic, three-dimensional shape of flapping insect wings may influence many aspects of flight performance. Insect wing deformations during flight are largely passive, and are controlled primarily by the architecture and material properties of the wing. Although many details of wing structure are well understood, the distribution of flexural stiffness in insect wings and its effects on wing...

نمودار تعداد نتایج جستجو در هر سال

با کلیک روی نمودار نتایج را به سال انتشار فیلتر کنید