Duplex stainless steel multi-pass welds were made at 0.15 MPa, 0.45 MPa, and 0.75 MPa pressure, simulating underwater dry hyperbaric welding by the flux-cored arc welding (FCAW) method, with welds of normal pressure as a benchmark. The purpose of this work was to estimate the effect of ambient pressure on the microstructure, pitting corrosion resistance and impact toughness of the weld metal. T...

Abstract— This paper develops a method of modelling and designing air-gapped ferrite inductor as filter for large current application of grid-tied inverter. The design method incorporates magnetization curve of the ferrite materials while the modelling of the inductor is based on inverse JilesAtherton model. The dynamic performance of the designed ferrite inductor in the DC-AC inverter circuit ...

ferrite sind magnetische werkstoffe, die in der technik vielseitige verwendung finden.z.b. ferritantennen, magnetophon, magnetische verstarker, magnetregler informationsspeicher,schaltelemente ; u.s.w. neue typen von ferriten erschlissen sich immer wieder neue anwendungsgebiete. die magnetische eigenschaft der ferrite hangen von der anordnung der atomen in kristallstruktur abo ferrite haben ein...

A new technique which allows the simulation of thin ferrite absorbing tiles in a coarse TLM mesh is described. Results are presented which show a good fit to manufacturers' reflectivity curves. Experimental and simulation results for a screened room partially lined with ferrite are presented to demonstrate the accuracy of the method. INTRODUCTION The Transmission Line Matrix (TLM) method of num...

Local electron work function, adhesive force, modulus and deformation of ferrite and austenite phases in a duplex stainless steel were analyzed by scanning force microscopy. It is demonstrated that the austenite has a higher electron work function than the ferrite, corresponding to higher modulus, smaller deformation and larger adhesive force. Relevant first-principles calculations were conduct...

Resonance experiments are described on polycrystalline ferrite spheres in a microwave cavity with a linearly polarized magnetic field. Fundamental quantities, like the g-factor and the damping coefficient 'of the ferrite, are derived from the measurements. The damping coefficient can be calculated either from a linewidth measurement or from the maximum amount of absorption in the ferrite at res...

New developments with bainite have resulted in a steel with an ultimate tensile strength of 2500 MPa, a hardness of 600-670 HV and a toughness in excess of 30-40 MPa m [1]. The novel microstructure is generated in a high carbon (0.98 wt.%) high silicon (1.46 wt.%) steel austenitized for 15 min. at 1000 oC, and then isothermally transformed at temperatures of ∼200 oC. Iron does not diffuse durin...

In this study, in vitro cytotoxicity of nickel zinc (NiZn) ferrite nanoparticles against human colon cancer HT29, breast cancer MCF7, and liver cancer HepG2 cells was examined. The morphology, homogeneity, and elemental composition of NiZn ferrite nanoparticles were investigated by scanning electron microscopy, transmission electron microscopy, and energy dispersive X-ray spectroscopy, respecti...

Arsenic (As) in groundwater and surface water is a worldwide problem possessing a serious threat to public health. In this study, a magnetic ferrite, was synthesized and investigated for its As(V) removal efficiency. The adsorption of As(V) by magnetic ferrite exhibited an L-shaped nonlinear isotherm, suggesting limiting binding sites on the adsorbent surface. The As K-edge X-Ray Absorption Nea...

Spatially Resolved X-Ray Diffraction (SRXRD) has been used to identify a previously unobserved low temperature ferrite (δ)/austenite(γ) phase transformation in the heat affected zone (HAZ) of 2205 Duplex Stainless Steel (DSS) welds. In this “ferrite dip” transformation, the ferrite transforms to austenite in the weld HAZ at peak temperatures on the order of 750oC. The austenite then re-transfor...