The Atraumatic Amniocentesis needle is manufactured by TSK Laboratory, Japan (Tochigi-Shi, Tochigi-Keri, 328 Japan). It is a 22 gauge, 90 mm needle. It has a pencil point tip with two circular holes at the tip. It is composed of a stainless steel AISI 304 with a polycarbonate hub. OD – 0.70±0.01 mm. ID – 0.40±0. 01 mm. Obturator length – 109.5±2 mm. OD of the obturator – 0.35±0.01 mm. Location ...

Thin alumina films, deposited at 280~ by low-pressure, metal-organic, chemical-vapor deposition on stainless steel, type AISI 304, were annealed at 0.17 kPa in a nitrogen atmosphere for 2, 4, and 17 hr at 600, 700, and 800~ The effect of the annealing process on the adhesion of the thin alumina films was studied using a scanning-scratch tester, type SST-IO1, developed by Shimadzu. The best mech...

Lie symmetry method is applied to find analytic solutions of initial-boundaryvalue problems of transient conduction in semi-infinite solid with constant surface temperature or constant heat flux condition. The solutions are obtained in a manner highlighting the systematic procedure of extending the symmetry method for a PDE to investigate BVPs of the PDE. A comparative analysis of numerical and...

To measure the cleanability of stainless steel surfaces under standardized conditions, a test stand was set up. Three stainless steel plates (size 200 x 100 mm) can be fixed to the test stand and sprayed with a water jet from a low-pressure nozzle for a period of several minutes. The plates were previously soiled with a starch or protein film with a pre-defined layer thickness and dried for sev...

This work reports on the influence of β-lactoglobuline (β-LGB) and of its denaturation on the adherence of quartz particles, taken as a model of particulate soil, on stainless steel AISI 304 with mirror finish. The substrate was soiled with quartz suspensions in water or in β-LGB solutions as such or previously heated at 75°C, and dried at room temperature or in an oven at 75°C. Cleanability wa...

The in-process monitoring and real-time control of the penetration depth during laser welding is evaluated. An optical collimator collects the optical emission for measurement with a fast spectrometer. The sensor data are used to calculate the electron temperature and subsequently to determine the weld quality of overlap welds in AISI 304 stainless steel sheets performed both with CW Nd:YAG and...

Micro Electric Discharge Machining is a nontraditional machining process which can be used for drilling micro holes in high strength to weight ratio materials. This present research study deals with the single optimization of micro EDM process using Genetic Algorithm. Mathematical models using Response Surface Methodology (RSM) is used to correlate the response and the parameters. The desired r...

In this study, two different vegetable based cutting fluids developed from refined canola and sunflower oil and a commercial type semi-synthetic cutting fluid were carried out to determine optimum conditions for tool wear and forces during milling of AISI 304 austenitic stainless steel. Taguchi L9 (3) orthogonal array was used for the experiment plan. Cutting speed, feed rate, depth of cut and ...

In this study, three different vegetable-based cutting fluids developed from raw and refined sunflower oil and two commercial types (vegetable and mineral based cutting oils), were carried out to determine for thrust force and surface roughness during drilling of AISI 304 austenitic stainless steel with HSSE tool. The uses of vegetable cutting oils was investigated in reducing thrust force and ...

In this paper, application of ultrasonic techniques for defect detection in weldments of austenitic stainless steel and maraging steel is discussed. Applications of ultrasonic techniques for characterizing microstructural changes in AISI type 316 stainless steel and modified 9Cr-1Mo ferritic steel; thermomechanical processing of 15Cr-15Ni-2.3Mo-titanium modified austenitic stainless steel (allo...