An improvement in the mechanical properties of a biomedical Ni-free Co-Cr-Mo alloy under as-cast condition has been examined by means of tensile tests and microstructure observations. The solubility of N in Co-Cr-Mo alloys increases with increasing Cr content from 29 to 34mass%. This results in a significant improvement in mechanical properties such as yield stress, tensile strength, and fractu...

This study reports on experiments where bismuth sesquioxide (Bi2O3) was cycled between its high-temperature d-phase and one or more of its low-temperature phases (a-, b-, or g-Bi2O3) while being subjected to uniaxial tensile stresses in the range of 0.11–0.55 MPa. Reproducible strain increments of 0.4%–3.9% have been measured after each thermal cycle, and total tensile fracture strains of 10%–2...

This work presents the effects of strain rate on the tensile properties and fracture morphologies of AHSS-DP 350/600 subjected to LSP. Fatigue crack growth test was performed to evaluate fatigue behavior in the metallic plate of AHSS-DP350/600. However, this material is used in automobile industry and enhancing it fatigue resistance is a challenge in material engineering. In order to evaluate a...

Arch dams are generally built in cantilvever monoliths. Vertical contraction joints between monoliths control the stresses due to concrete shrinkage and temperature variations. Past studies in earthquake safety evaluation of the system often show the tensile fracture and local nonlinear deformation of joints. In this paper, some nonlinear joint element constitutive models are presented to exami...

Low, intermediate and high strain rate tensile experiments are carried out on flat smooth, notched and central-hole tensile specimens extracted from advanced high strength steel sheets. A split Hopkinson pressure bar testing system is used in conjunction with a load inversion device to perform the high strain rate tension experiments. Selected surface strains, as well as local displacements, ar...

Mechanical properties of dissimilar weld joints between GOST09ch16N4B (a martensitic stainless steel) and AISI 4130 thin sheets made by gas tungsten arc welding (GTAW) were studied using ER410NiMo and ER100S-G filler metals in post weld heat treated conditions. Heat treatment cycles consisted of austenitization at 900, 950 and 1000 °C for 1 h and this was followed by oil cooling and tempering a...

With the recent development of 3D printing technology, concrete materials are sometimes used in 3D printing. Concrete structures based on 3D printing have been characterized to have the form of multiple layer build-up. Unlike general concrete structures, therefore, the 3D-printed concrete can be regarded as an orthotropic material. The material property of the 3D-printed concrete’s interface be...

Lignocellulosic fibers from green coconut fruit were treated with alkaline solution (NaOH 10%m/v) and then bleached with sodium chlorite (NaClO2) and acetic acid (CH3COOH). Alkali-treated and bleached fibers were mixed with high impact polystyrene (HIPS) and placed in an injector chamber in order to obtain specimens for tensile tests. Specimens of HIPS/alkali-treated and bleached coconut fiber ...

&bstracL Planar impact experiments were employed to induce dynamic tensile failure in Bedford limestone. Rock discs were impacted with aluminum and polymethyl methacralate (PMMA) flyer plates at velocities of 10 to 25 m/s. Tensile stress magnitudes and duration were chosen so as to induce a range of microcrack growth insufficient to cause complete spalling of the samples. Ultrasonic Pand S-wave...

Graphene nanoplatelets (GNPs) are added as reinforcement to ultrahigh molecular weight polyethylene (UHMWPE) with an intended application for orthopedic implants. Electrostatic spraying is established as a potential fabrication method for synthesizing large-scale UHMWPE-GNP composite films. At a low concentration of 0.1 wt % GNP, the composite film shows highest improvement in fracture toughnes...