The aim of this study was to evaluate the effect of remaining dentin thickness (RDT) on resin composite bond strength to dentin surfaces when using various adhesive systems. One of three adhesives, Clearfil SE Bond, Single Bond or Clearfil Tri-S Bond, followed by Z100 resin composite were built up on flat dentin surfaces of human molars. The teeth were sectioned obtaining beams with crosssectio...

The shear bond strength of composite resin to porcelain was investigated to optimize variables for bonding porcelain laminate veneers. Scanning electron microscopy was initially used to examine the surface configuration of porcelain prepared under various conditions. A factorial experiment was undertaken to determine the effects of three different bonding methods on both etched and non-etched p...

Self-etch adhesives that etch, prime, and bond simultaneously should not exhibit incomplete resin infiltration within hybrid layers. We hypothesized that nanoleakage patterns in these systems are artifacts caused by mineral dissolution in mildly acidic silver nitrate. Resin-dentin interfaces bonded with four single-step, self-etch adhesives were examined for nanoleakage by conventional (pH 4.2)...

The objective of this study was to improve interfacial adhesion properties at the interface of thermomechanical pulp (TMP) fiber and isotactic polypropylene (iPP) using thermoset adhesives such as phenol formaldehyde (PF) and urea formaldehyde (UF). This study also attempted to achieve fiber-to-fiber adhesion using thermoset adhesives before the molten iPP would flow into the fiber web. The fra...

Microleakage is related to recurrent decay, inflammation of vital pulps, and reinfection of previously treated root canals. The purpose of this investigation was to compare the abilities of new adhesive cements and conventional nonadhesive controls to prevent microleakage under stainless steel crowns on primary anterior teeth. Standardized preparations were made, and stainless steel crowns were...

OBJECTIVES To evaluate the effect of different bonding strategies on the microtensile bond strength to deep and superficial permanent dentin. METHODS Forty-eight teeth were randomly flattened according to the dentin depth: superficial dentin (SD) and deep dentin (DD). Subsequently, three adhesive systems were applied (n=8): an etch-and-rinse (Adper Single Bond 2 - SB), a "mild" two-step self-...

In vitro tensile bond strengths were determined for three adhesive cements and two resin-bonded bridge cements to two alloys, each prepared by two methods: sandblasted Ni-Cr-Be alloy (I), electro-etched Ni-Cr-Be alloy (II), sandblasted Type IV gold alloy (III), and tin-plated Type IV gold alloy (IV). Storage conditions of 24 hours at 37 degrees C and 30 days at 70 degrees C were evaluated. The ...

The aim of this study was to compare the shear bond strengths (SBS), failure modes (adhesive, cohesive, or mixed), and marginal microleakage occurrence of conventional resin (CR)-based, glass ionomer (GI)-based, and self-adhesive resin (SAR)-based fissure sealants with or without prior phosphoric acid (PA) etching. Fifty extracted premolars were randomly and equally assigned into five groups -G...

The purpose of this study was to evaluate the effects of acidic primers on adhesive bonding to sintered aluminum oxide (alumina). Alumina disks were primed with one of the following materials: Acryl Bond, All Bond 2 Primer B, Alloy Primer, Estenia Opaque Primer, Eye Sight Opaque Primer, M.L. Primer, MR. Bond, and Super-Bond Liquid. Specimens were then bonded with an acrylic resin initiated with...

It has been reported that the adhesive resin layer of all-in-one adhesives is permeable and allows the formation of a water channel or water tree. The effects of a smear layer on the ultra-structure of bonding interface created with three all-in-one adhesives and a resin composite were evaluated in this study. Dentin surface was ground with of 180-, 600-, or 2000-grit SiC paper to produce diffe...