نتایج جستجو برای: aluminum alloy 5052

تعداد نتایج: 96621  

A. Qaed Amini Haroooni, H. Eskandari, I. Danaee, M. H. Maddahy,

The electrochemical behavior of 6063 aluminum alloy in ethylene glycol-water mixture was investigated by polarization curves and AC impedance measurements (EIS).  The results obtained from polarization curves showed that corrosion rate decreased with increasing ethylene glycol concentration. EIS data showed the decrease in the interface capacitance which caused by adsorption of ethylene glycol ...

2004
Makoto Saga Masao Kikuchi

Aluminum alloys of the 6xxx series which contain excess Si or Cu are well used for the automotive applications because of the high age-hardening response. The effect of addition of small amount of Sn on the two-step aging behavior in 1.2%Mg2Si-0.5%Si in excess alloy and 1.2%Mg2Si-0.7%Cu alloy was investigated by means of hardness measurement, differential scanning calorimetry, and transmission ...

2008
Chaohua FAN Yuting HE Hengxi ZHANG Hongpeng LI Feng LI

In the paper, genetic algorithm is introduced in the study of network authority values of BP neural network, and a GA-NN algorithm is established. Based on this genetic algorithm-neural network method, a predictive model for fatigue performances of the pre-corroded aluminum alloys under a varied corrosion environmental spectrum was developed by means of training from the testing dada, and the f...

Burnishing is a chip-less finishing process, in which a hard roller or ball presses the surface layer of part to perform plastic deformation in the surface layer and produce improved finish, enhanced hardness and compressive residual stresses on the surface of special materials such as Aluminum and Brass. In the following research, the effect of input parameters such as feed rate, cutting speed...

Journal: :journal of modern processes in manufacturing and production 2014
mohammad hossein shahsavari farshid ahmadi

nowadays, equal channel angular pressing, known as the ecap process, is one of the most popular methods for manufacturing ultra-fine grained (ufg) materials. in this paper, ecap process has been carried out on pure copper and 6012 aluminum alloy up to six passes by route . principal attention was paid to the influence of parameters such as diameter, material, and the height of billet on mechani...

2001
E. G. Herbert J. L. Hay

It has been proposed that with the appropriate models, instrumented indentation test (IIT) data can be reduced to yield the uniaxial stress–strain behavior of the test material. However, very little work has been done to directly compare the results from uniaxial tension and spherical indentation experiments. In this work, indentation and uniaxial tension experiments have been performed on the ...

2008
Zhanfeng YANG Weibin ZHANG Yong TIAN Zhenquan LI Hehou ZONG

The working principle of scanning acoustic microscope (SAM) is introduced, and the acoustic transmission action is analyzed according to the geometrical and structural characteristics of explosive/Aluminum-alloy binding. The adhesive status of the interface in some typical parts of the binding is detected by SAM and 30MHz ultrasonic focal field lens. The results show that the interfaces between...

2016
Uday Sen Kulbhushan Sharma

In this investigation, the effect of friction stir processing (FSP) parameters such as rotational speed, traverse speed and plunge depth on the tensile strength of AA6063 aluminum alloy was studied. The experiments were carried out as per response surface methodology parametric design concepts to study the influence of various combinations of process parameters. Statistical optimization techniq...

Journal: :Microscopy and microanalysis : the official journal of Microscopy Society of America, Microbeam Analysis Society, Microscopical Society of Canada 2013
Seung-Jun Lee Min-Su Han Seong-Jong Kim

The technological development of all kinds of lightweight transportation devices including vehicles, aircraft, ships, etc. has progressed markedly with the demand for energy saving and environmental protection. Aluminum alloy is in the spotlight as it is a suitable environmentally friendly material. However, deformation is a major problem during the welding process because aluminum alloy has a ...

نمودار تعداد نتایج جستجو در هر سال

با کلیک روی نمودار نتایج را به سال انتشار فیلتر کنید