This investigation is focused on the corrosion evaluation of an as-cast Al-Si alloy, obtained by two different casting methods: traditional sand and three-printing casting, using a binder jetted mold. The experimental results are discussed in terms chemical composition, microstructure, hardness, behavior parts. microstructure composition sample before after tests was analyzed light microscopy (...

The inhibitive action of alkali extract human hair extract (Bio waste) against the corrosion of mild steel (98.58%) in solutions of nitric acid has been studied using potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). At inhibitor concentration range (0.004 % v/ v to 0.1% v/v) in 0.3 M HNO3acid, the results showed that these compounds suppressed both cathodic and ano...

We investigated the underlying physical and chemical causes of the improvement of electrochemical activity of the cathode in solid oxide fuel cells (SOFC) under long term cathodic or anodic polarization, termed ‘current conditioning’, through in situ X-ray absorption spectroscopy (XAS). The electrodes were powder La0.8Sr0.2MnO3 (LSM) made with glycine-nitrate process and thin films of LSM and L...

Biocompatibility of electrodes for stimulation are difficult to maintain homeostasis. Noble metal stimulating electrodes which are normally biocompatible on keratinized tissue become very non-biocompatible when they are interfaced with nonkeratinized tissue in an area such as the oral cavity. Composite electrodes have been made biocompatible in the oral cavity even at current densities larger t...

Pitting corrosion was observed on a high purity Fe-17Cr alloy in 0.02M NaCl solution of pH 6.6 at high anodic potential (+ 550 mVISCE). Potentiostatic electrochemical noise measurements were performed, revealing the presence of a characteristic current noise below stable pitting, differing strongly from that observed 011 a series of AISI 430 type 17% Cr stainless steels, with respect to the fre...

The paper presents influence of mechanical surface damage on corrosion resistance of plates made of Cr-Ni-Mo stainless steel, used in funnel chest treatment. The surface of the steel was electrochemically polished and fitted. The surface damage is induced in the given deformation regions and is a potential reason of corrosion. The corrosion tests were realised by recording of anodic polarizatio...

This Module consists of ten Web pages of required reading. The pagination is visible at the bottom of each page with direct links to adjacent pages. Introduction Thermodynamic principles can help explain a corrosion situation in terms of the stability of chemical species and reactions associated with corrosion processes. However, these principles cannot be used to predict corrosion currents or ...

The aim of this present work is to study, the corrosion behavior of carbon steel in well water in the presence of sodium tungstate (ST)-Zn 2+ -N-(phosphenomethyl) iminodiaceticacid (NPMIDA) solutions. Electrochemical studies and FTIR spectral studies and weight loss study have been employed. It was found that the inhibition efficiency (IE) of ST (50 ppm)-Zn 2+ (10 ppm) was improved from 8% to 8...

The corrosive behavior of Ti and its alloys in fluoride media is well known. Based on electrochemical studies, this paper describes the effect of fluoride ions on the passive behavior of Ti6Al4V alloy in lactated Ringer’s serum. The open circuit potential of the alloy in the serum, which lies in the passive region of TiO 2 , shifts to more negative values as fluoride ions are added. The voltamm...

The inhibition effect of N-benzyl-N′-phenyl thiourea (BPTU) on the corrosion of mild steel in 0.01 and 0.05 N HCl medium has been investigated by potentiostatic polarization technique. Results obtained reveal that BPTU is an efficient anodic inhibitor with greater than 94% of efficiency in the range of temperature studied. The adsorption of inhibitor on the mild steel surface obeys the Temkins’...