نتایج جستجو برای: cold work tool steel

تعداد نتایج: 1429159  

2016
Niclas Ånmark Andrey Karasev Pär Göran Jönsson

This study focused on the evaluation of the machinability of different carburising steel grades by using a cemented carbide cutting tool during semi finishing of steel. The effect of the steel composition, microstructure and inclusion characteristics on the cutting tool wear in the soft part turning was evaluated for a reference steel R (0.028% S, 0.0009% O), a clean C steel (0.003% S, 0.0005% ...

2015
V. Sathiyamoorthy T. Sekar N. Elango

Formation of spikes prevents achievement of the better material removal rate (MRR) and surface finish while using plain NaNO3 aqueous electrolyte in electrochemical machining (ECM) of die tool steel. Hence this research work attempts to minimize the formation of spikes in the selected workpiece of high carbon high chromium die tool steel using copper nanoparticles suspended in NaNO3 aqueous ele...

Journal: :international journal of iron & steel society of iran 2015
m. golzar shahri m. salehi s. r. hosseini

the mechanical properties and microstructural developments of 321 stainless steel during thermomechanicalprocess were investigated. the repetitive cold rolling and subsequent annealing wereconducted to achieve nanocrystalline structure in an aisi 321 stainless steel. heavily cold rolling at−20°c was conducted to form martensite in metastable austenitic steel. the process was followed byannealin...

2007
T. Davidek Z. Dolezal Suk P. Tas S. Valkar

In the paper we rewiev the experience with the steel from Cold Rolling Mill Kraluv Dvur near Prague, where the steel for barrel module 0 prototype of the TILECAL calorimeter was fabricated. The measurements of the tolerances, mechanical properties and the chemical composition are presented.

Journal: :Nanoscale 2014
Bo Li Jin-Ming Wu Tao-Tao Guo Ming-Zao Tang Wei Wen

A facile solution-based technique was developed to grow vertically aligned TiO2 nanowires with predominantly anatase phase on arbitrary substrates of stainless steel, glass, silicon wafer and carbon cloth at the low temperature of 80 °C and in an open atmosphere.

2013
A. Li

Article history: Received 10.9.2012 Received in revised form 10.12.2012 Accepted 10.12.2012 27SiMn steels with different original structures were zero time holding quenched after pretreatments including general quenching and normalizing, respectively, then their tensile strength and hardness were determined and also microstructures were analyzed.. The experimental results show that thus quenche...

2006
J. P. Ferrer C. Capdevila F. G. Caballero C. García de Andrés

Pearlitic steels present very interesting mechanical properties when weldability requirements are not too severe. Thin gauge pearlitic steels require at least one intermediate annealing treatment between hot rolling and cold rolling. The globularised cementite in medium carbon steels provides then higher ductility, formability and machinability. On the other hand, in-line induction heating devi...

2015
Jiang Bin Zhang Wei

In view of the unstable cutting problem in the process of high speed milling hardened steel. Conduct experiment of the stability of machine tool and high speed milling cutter. The machine tool spindle vibration spectrum and vibration acceleration signal under the condition of different centrifugal force were detected. Obtained the critical speed of security and stability cutting of milling cutt...

2017
Yassmin Seid Ahmed German Fox-Rabinovich Jose Mario Paiva Terry Wagg Stephen Clarence Veldhuis

During machining of stainless steels at low cutting -speeds, workpiece material tends to adhere to the cutting tool at the tool-chip interface, forming built-up edge (BUE). BUE has a great importance in machining processes; it can significantly modify the phenomenon in the cutting zone, directly affecting the workpiece surface integrity, cutting tool forces, and chip formation. The American Iro...

نمودار تعداد نتایج جستجو در هر سال

با کلیک روی نمودار نتایج را به سال انتشار فیلتر کنید