This study evaluated in vitro the influence of a temporary filling {zinc oxide-eugenol (ZOE)} and two pulpotomy agents {formocresol (FC) and ferric sulfate (FS)} on shear bond strength (SBS) of two dentin adhesives to the dentin of primary molars. A total of 80 dentin surfaces were prepared and randomly allocated into 10 groups of 8 specimens each. Groups were subjected to different treatments,...

OBJECTIVES This study investigated the effect of extreme cooling methods on the flexural strength, reliability and shear bond strength of veneer porcelain for zirconia. METHODS Vita VM9 porcelain was sintered on zirconia bar specimens and cooled by one of the following methods: inside a switched-off furnace (slow), at room temperature (normal) or immediately by compressed air (fast). Three-po...

introduction: the aim of this study was to compare the micro-shear bond strength of composite resin on superficial and deep dentin after conditioning with phosphoric acid and erbium-doped yttrium aluminum garnet (er:yag) laser. methods: thirty human molars were selected, roots were removed and crowns were bisected to provide a total of 60 half-crowns. specimens were ground to expose superficial...

BACKGROUND Disinfection of dentin surface prior to any restorative therapy is important for the longevity of the treatment rendered. However, these dentin disinfection methods should itself not interfere with the adhesion of the restorative material. Therefore the aim of this study was to determine the effect of various dentin disinfection protocols on the shear bond strength (SBS) of resin mod...

BACKGROUND The effects of fluoride and CPP-ACP before bracket bonding on the shear bond strength of orthodontic brackets have been reported with contradicting results. The objective of this in vitro study was to evaluate the effect of different preventive agents namely; casein phosphopeptide-amorphous-calcium-phosphate (CPP-ACP), fluoride-containing-CPP-ACP (CPP-ACPF) and 5% sodium fluoride (5%...

The purpose of this study was to evaluate the shear bond strength (SBS) of two different resin cements (Panavia F 2.0 (Kuraray Medical Inc, Okayama, Japan) and Variolink N (Ivoclar Vivadent AG, Schaan, Liechtenstein)) to 112 zirconia specimens with airborne-particle abrasion and 20%, 30%, or 40% hydrofluoric acid (HF) for 1 or 2 h. A total of eight specimens were used to observe the phase trans...

background: the clinical success of sandwich technique depends on the strength of resin-modified glass ionomer cement (rmgic) bonding to both dentin and resin composite. therefore, the shear bond strength (sbs) of resin composite bonded to rmgic utilizing different resin adhesives versus a gic-based adhesive was compared. materials and methods: in this in vitro study, 84 holes (5×2 mm) were pre...

Aim: This study investigated the effect of various surface treatments on bond strength a universal adhesive to demineralized dentin. Materials and Methods: Human dentin surfaces forty-eight carries-free maxillary premolars were prepared by acidic solutions. Teeth randomly distributed into four groups (n=12) getting different treatments. Three minutes application CPP‑ACP (group 1), Er: YAG laser...

INTRODUCTION The purpose of this study was to compare shear bond strength (SBS) of orthodontic brackets bonded to enamel prepared by Er:YAG laser with two different powers and conventional acid-etching. MATERIALS AND METHODS Forty-five human premolars extracted for orthodontic purposes were randomly assigned to three groups based on conditioning method: Group 1- conventional etching with 37% ...

BACKGROUND Detachment of denture acrylic resin artificial teeth from denture base resin is one of the most common problems presented by denture wearers. PURPOSE This study investigated the shear bond strength (SBS) and fracture type of bonding interface of two commercial acrylic teeth (Vipi Dent Plus e Biolux) to two denture base resins (Vipi Cril e Lucitone 550) after immersion in potentiall...