Tire derived aggregate (TDA) has been proposed as a possible lightweight replacement for mineral aggregate in concrete. The role played by the amount of TDA replacing coarse aggregate as well as different treatment and additives in concrete on its properties is examined. Conventional concrete (without TDA) and concrete containing TDA are compared by examining their compressive strength based on...

For optimum production of ultra-high performance concrete (UHPC), the material and microstructural properties of UHPC cured under various heat treatment (HT) conditions are studied. The effects of HT temperature and duration on the hydration reaction, microstructure, and mechanical properties of UHPC are investigated. Increasing HT temperature accelerates both cement hydration and pozzolanic re...

This paper presents the effect of Sodium Chloride (NaCl) on Conventional Concrete (Silica Fume Based M30 Grade Concrete). The Silica Fume Based M30 Grade Concrete was prepared by adding NaCl concentrations of 0.5,2,4,6,8,10 and 12 g/l i n deionised water. In addition to this, control specimen was prepared with deionised water (without NaCl) for the purpose of co mpari son . The tensile strength...

Gelatin films were prepared by casting. Tensile strength (TS) and elongation at break (Eb) of the gelatin films were found to be 46 MPa and 3.5%, respectively. Effect of gamma radiation (Co-60) on the thermo-mechanical properties of the gelatin films was studied. 2-hydroxyethyl methacrylate (HEMA) was added to the gelatin during casting varying (10% 30% by weight) and found to increase the TS s...

OBJECTIVE The purpose of this study was to investigate the effects of two curing light intensities on the mechanical properties (Vickers microhardness, compressive strength, and diametral tensile strength) of bulk-fill resin-based composites (RBCs). MATERIALS AND METHODS Four commercially available bulk-fill RBCs (Tetric® N-Ceram, SonicFill™, Smart Dentin Replacement (SDR™) Posterior Flowable...

[1] The mechanical behavior of hydrate-bearing sediments subjected to large strains has relevance for the stability of the seafloor and submarine slopes, drilling and coring operations, and the analysis of certain small-strain properties of these sediments (for example, seismic velocities). This study reports on the results of comprehensive axial compression triaxial tests conducted at up to 1 ...

Over a million tonnes of cigarette butts (CBs) are produced worldwide annually. These CBs accumulate in the environment due to the poor biodegradability of the cellulose acetate filters and pose a serious environmental risk. This paper presents some of the results from a continuing study on recycling CBs into fired clay bricks. Properties including compressive strength, flexural strength, densi...

This study focuses on the effect of the amount of silica fume addition and volume fraction of steel fiber on the engineering properties of cementitious materials. Test variables include dosage of silica fume (5% and 10%), water/cement ratio (0.35 and 0.55) and steel fiber dosage (0.5%, 1.0% and 2.0%). The experimental results included: compressive strength, direct tensile strength, splitting te...

The aim of this study was to compare, in different periods of time, the compressive and diametral tensile strength of a traditional high viscous glass ionomer cement: Fuji IX (GC Corporation), with two new Brazilian GIC's: Vitro-Molar (DFL) and Bioglass R (Biodinamica), all indicated for the Atraumatic Restorative Treatment (ART) technique. Fifteen disk specimens (6.0mm diameter x 3.0mm height)...

The kinetics of Mn(VII) oxidation of lysine in moderately sulfuric acid solutions was studiedspectrophotometrically in the presence and absence of Mn(II) as catalyst. The reaction was arrangedto be under pseudo first-order condition with respect to Mn(VII). The results showed that the pseudofirst-order rate constant increases with increasing [H2SO4], [(Mn)II], and [lysine]. The dependence ofthe...