Two different ionic liquids have been tested in the electrochemical fabrication of anodic porous alumina in an aqueous solution of oxalic acid. It was found that during galvanostatic anodization of the aluminum at a current density of 200 mA/cm2, addition of 0.5% relative volume concentration of 1-butyl-3-methylimidazolium tetrafluoborate resulted in a three-fold increase of the growth rate, as...

Self-assembled monolayers (SAMs) of 4'-methylbiphenyl-4-thiol (MBP0) adsorbed on polycrystalline gold substrates served as templates to control electrochemical deposition of Cu structures from acidic solution, and enabled the subsequent lift-off of the metal structures by attachment to epoxy glue. By exploiting the negative-resist behaviour of MBP0, the SAM was patterned by means of electron-be...

Lithol Rubine B (LRB; the disodium salt of 3-hydroxy-4-[(4-methyl-2-sulfophenyl) azo]-2-naphthalenecarboxylic acid) was detected using high-performance liquid chromatography with an electrochemical (antimony film on silver) detector (HPLC-ECD). For direct current (DC) mode, with the current at a constant potential, and measurements with suitable experimental parameters, a linear concentration f...

one of the problems in the case of stainless steels is their low corrosion resistance against pitting corrosionin chloride containing environments, thereby leading to severe damage to industries. in this research, the pitting corrosion of 304 austenitic stainless steel was studied in 3.5% nacl solution at room temperature (25˚c) by performing electrochemical measurements (containing cyclic pola...

Abstract The influence of branched N , ′-bis( p -hydroxybenzoyl) containing propylenediamine (PDA) and triethylenetetramine (TETA) composites for corrosion inhibition carbon steel in acidic solution (1 M HCl) was investigated using several quantum chemical, electrochemical impedance spectroscopy potentiodynamic polarization as techniques. molecules were posteriorly characterized by proton nucle...

The hydrogen evolution reaction (HER) on an electrodeposited a-MoS2 electrode was investigated by a surface-selective electrochemical titration technique by application of surface interrogation scanning electrochemical microscopy. In a mildly acidic (pH 4.6) environment, the saturated surface hydride coverage of MoS2 was determined to be 31%, much higher than that expected for a crystalline nan...

The paper describes the electronic charging and conducting properties of vertically oriented TiO 2 nanotube arrays formed by anodization of Ti foil samples. The resulting films, composed of vertically oriented nanotubes approximately 10 mum long, wall thickness 22 nm, and pore diameter 56 nm, are analyzed using impedance spectroscopy and cyclic voltammetry. Depending on the electrochemical cond...

A new cathodic material for electro-Fenton (EF) process was prepared based on a macroscopic fiber (CNTF) made of mm-long carbon nanotubes directly spun from the gas phase by floating catalyst CVD, on a carbon fiber (CF) substrate. CNTF@CF electrode is a highly graphitic material combining a high surface area (~260 m2/g) with high electrical conductivity and electrochemical stability. One kind o...

In this study, electrochemical behaviour of passive films formed on AISI 316L stainless steel (AISI 316L) in three acidic solutions concentrations (0.3, 0.6, and 0.9M HNO3) under open circuit potential conditions were evaluated by potentiodynamic polarization, Mott–Schottky analysis and electrochemical impedance spectroscopy (EIS) techniques. The potentiodynamic polarization results showed that...

Acidic electrolytes are advantageous for water electrolysis in the production of hydrogen as there is a large supply of H(+) ions in the solution. In this study, with the applied overpotential larger than the equilibrium potential of Ni(0)/Ni(2+), Ni foam as HER electrode exhibits excellent and stable HER activity with an onset potential of -84 mV (vs RHE), a high current density of 10 mA cm(-2...