Graphene oxide (GO) can be readily modified for particular applications due to the existence of abundant oxygen-containing functional groups. Graphene oxide-based materials (GOBMs), which are biocompatible and hydrophilic, have wide potential applications in biomedical engineering and biotechnology. In this review, the preparation and characterization of GO and its derivatives are discussed at ...

This paper describes the results of tests on the influence of human saliva and its substitutes on tribological characteristics of friction pairs. Each pair consists of enamel and one of the following materials: ceramics, the Meridian B2 dental composite, the GK dental amalgam, and Ti-6Al-4V titanium alloy. The saliva substitutes used were prepared using pyrophosphates, xanthan gum, and mucins d...

Nitrile-butadiene rubber (NBR) and another polymer with an excellent self-lubricating property are blended to develop a new kind of polymer used for water-lubricated stern bearings. The tribological performance of the new Polymer Blend of NBR (PBN), with the comparison of a rubber common used for most stern bearings, was studied using a stern bearing test rig of SSB-100. The results showed that...

Biodiesels are a renewable energy source, and they have the potential to be used as alternatives to diesel fuel. The aim of this study is to investigate the wear and friction characteristics of Australian native first generation and second generation biodiesels using a four-ball tribo tester. The biodiesel was produced through a two-step transesterification process and characterized according t...

Pure carbon(C), nitrogen(N) and titanium(Ti) doped diamond-like carbon (DLC) coatings were deposited on silicon (Si) micro-molds by dc magnetron sputtering deposition to improve the tribological performance of the micro-molds. The coated and uncoated Si molds were used in injection molding for the fabrication of secondary metal-molds, which were used for the replication of micro-fluidic devices...

Tribological properties of nanolamellar tungsten disulfide doped with zinc oxide nanoparticles were studied. Nanolamellar tungsten disulfide and ZnO nanoparticles produced by electrospark erosion of metal granules in an H2O2 solution were analyzed using the XRD, SEM and TEM techniques. According to the tribological measurements, ZnO nanoparticles did not significantly change the friction coeffi...

Citation: Barnhill WC, Gao H, Kheireddin B, Papke BL, Luo H, West BH and Qu J (2015) Tribological bench and engine dynamometer tests of a low viscosity SAE 0W-16 engine oil using a combination of ionic liquid and ZDDP as anti-wear additives. Front. Mech. Eng. 1:12. doi: 10.3389/fmech.2015.00012 Tribological bench and engine dynamometer tests of a low viscosity SAE 0W-16 engine oil using a combi...

AbstractSputtered MoS2 coatings have been mostly used as a solid lubricant. In this investigation, MoSx/Ni composite coatings with Ni contents varying from 0 to 22 % were deposited onto steel substrate using a DC magnetron sputter process. The MoS2/Ni ratio in the coatings was controlled by sputtering the composite targets. The composition, microstructure, and mechanical properties of the...

BACKGROUND Total meniscectomy has been shown to cause early-onset arthritis in the underlying cartilage and bone in the knee joint, demonstrating that the meniscus plays an important protective role in the load carrying capacity. Relationships between friction and wear in synovial joints are complex due to the biphasic nature of articular cartilage and the time dependency of tribological respon...

Cu/Ti3SiC2/C/BN/GNPs nanocomposites were prepared by vacuum hot-pressing (HP) sintering and hot isostatic pressing (HIP) sintering methods. Microstructures, mechanical and tribological properties of Cu/Ti3SiC2/C/BN/GNPs nanocomposites were investigated. Microstructures were examined by optical microscopy (OM), X-ray diffraction (XRD) and scanning electron microscope (SEM). Mechanical properties...