کریم زاده, فتح اله
دانشکده مهندسی مواد، دانشگاه صنعتی اصفهان
[ 1 ] - سنتز و مشخصه‌یابی پوشش نانوکامپوزیت FeAl/Al2O3 بر زیرلایه فولادی تولید شده به‌روش آسیا‌کاری گلوله‌ای پرانرژی
In the present study, FeAl/Al2O3 nanocomposite coating was produced on the carbon steel plate using mechanical alloying (MA) technique via a mechanochemical reaction. Stoichiometric ratios of Fe, Al and Fe2O3 as well as a substrate were mixed and milled up to 22h in a vibrating high energy mill with a 4 mm ball. Samples prepared after 18h of MA were subjected to annealing at 773 K for 1-3 h. X-...
[ 2 ] - بررسی خواص مکانیکی و ریز ساختاری اتصال نفوذی TLP نانوکامپوزیت Al2O3p/Alبا استفاده از لایه واسطه مس
Due to their superior properties such as high specific strength, high creep resistance and high strength at elevated temperatures, aluminum composites reinforced with alumina nano particles are widely used for advanced purposes such as aerospace and auto industries. Lack of an appropriate welding process limits their applications. Transient liquid phase (TLP) bonding is one of the state-of-the...
[ 3 ] - سنتز گرافن سه بعدی و بهینه‌سازی مورفولوژی آن
Due to electrical properties (high electron mobility) and electrochemical characteristics (high electron transport rate), graphene-based materials have been widely applied for various scientific fields. However, due to their two-dimensional structures, these materials have low active sites for reaction. Therefore, changing from two-dimensional sheets dimensional to the three-dimensi...
[ 4 ] - ساخت کامپوزیت سطحی AZ91/MgxCuy، با استفاده از فرایند اصطکاکی اغتشاشی و بررسی رفتار سایشی آن پس از عملیات حرارتی T6
در این پژوهشکامپوزیت سطحی بر پایه‌ی سیستم Mg-Cu، و با استفاده از فرایند اصطکاکی اغتشاشی به صورت درجا بر سطح آلیاژ AZ91C ایجاد شد. بررسی میکروساختار منطقه‌ی اغتشاش پس از شش پاس فرایند نشان‌دهنده‌ی تشکیل ترکیب بین‌فلزی Mg2Cu در کامپوزیت AZ91/Cu است. بعد از عملیات حرارتی T6 با افزایش درصد حجمی ذرات تقویت‌کننده و تشکیل ترکیب بین‌فلزی MgCu2، سختی نمونه‌ی کامپوزیتی افزایش یافت. ...
[ 5 ] - Evaluation of microstructure and mechanical properties of bulk nanostructured Ti5Si3 and Ti5Si3-Al2O3 nanocomposite
Mechanical alloying and vacuum sintering have been used to produce bulk nanostructured Ti5Si3 and Ti5Si3-15Wt.% Al2O3 nanocomposite. X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM) were used to study the microstructural characteristics of the samples. Indentation method was used to calculate hardness, elastic modulus and fracture toughness ...
[ 6 ] - Investigating the Joining of Ni3Al Intermetallic Compound, using Transient Liquid Phase (TLP) Method with Cu Interlayer
In this study, joining of Ni3Al intermetallic compounds using the transient liquid phase (TLP) process with Cu interlayer was investigated. The binding process was carried out in a vacuum furnace at a temperature of 1050 °C for different times of 30, 60, 90 and 120 minutes. The effect of time variation on microstructure and mechanical properties of the joint zone was investigated. The EDS analy...
[ 7 ] - Development of Copper-Ferrite Spinel Coating on AISI 430 Steel Used as Solid Oxide Fuel Cell
The bare and pre-oxidized AISI 430 pieces were screen printed by copper ferrite spinel coatings. Good bonding between the coating and the substrate was achieved by the reactive sintering process of the reduced coating. The energy dispersive X-ray spectroscopy (EDS) analysis revealed that the scale is a double layer consisting of a chromia-rich subscale and an outer Cu/Fe-rich spinel. The result...
[ 8 ] - Development of Copper-Ferrite Spinel Coating on AISI 430 Steel Used as Solid Oxide Fuel Cell
The bare and pre-oxidized AISI 430 pieces were screen printed by copper ferrite spinel coatings. Good bonding between the coating and the substrate was achieved by the reactive sintering process of the reduced coating. The energy dispersive X-ray spectroscopy (EDS) analysis revealed that the scale is a double layer consisting of a chromia-rich subscale and an outer Cu/Fe-rich spinel. The result...
[ 9 ] - resistance spot welding of nanostructured Al 2024 alloy and Evaluation of mechanical properties Weldment
In this research in order to improve the mechanical properties of Aluminium alloy 2024, nanostructure Aluminum sheets were first produced by Cryorolling process and then was welded by resistance spot welding method. For this purpose, the samples solution treated at 495˚C for 55 minute and subsequently cryorolled up to 85% reduction in thickness. For obtaining simultaneous strength and ductility...
[ 10 ] - resistance spot welding of nanostructured Al 2024 alloy and Evaluation of mechanical properties Weldment
In this research in order to improve the mechanical properties of Aluminium alloy 2024, nanostructure Aluminum sheets were first produced by Cryorolling process and then was welded by resistance spot welding method. For this purpose, the samples solution treated at 495˚C for 55 minute and subsequently cryorolled up to 85% reduction in thickness. For obtaining simultaneous strength and ductility...
نویسندگان همکار