Unraveling the Effects of Process Control Agents on Mechanical Alloying of Nanostructured Cu-Fe Alloy

نویسندگان

  • Abolghasem Ataie School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, P.O. Box 11155-4563, Tehran, Iran
  • Hamed Mirzadeh School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, P.O. Box 11155-4563, Tehran, Iran
  • Mina Rabiee School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, P.O. Box 11155-4563, Tehran, Iran
چکیده مقاله:

Nanostructured Cu-20Fe alloy was synthesized by mechanical alloying process and the effects of process control agents (PCA) on the phase formation, crystallite refinement and morphology of powder particles were studied. The dissolution of Fe into Cu matrix and the morphology of powder particles were analyzed by X-ray diffraction (XRD) technique and scanning electron microscopy (SEM), respectively. The mean crystallite size was approximated by the method developed by Williamson and Hall. It was found that in the absence of PCA (Toluene in the present work), the iron peaks vanish after 5 h of mechanical alloying process and the mean crystallite size of the matrix decreases to 35 nm and large agglomerated particles are formed during milling. In this regard, it was found that the addition of PCA decreases the rate of crystallite refinement and formation of solid solution but does not affect the final mean crystallite size. It was also found that the addition of PCA during milling decreases the powder particle size considerably and by preventing agglomeration can lead to a finer powder particle size compared with the initial unmilled powders. It was also revealed that the effect of PCA on particle size is much greater than the effect of milling time.

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Aging of a nanostructured Zn50Se50 alloy produced by mechanical alloying

The aging of a nanocrystalline equiatomic ZnSe alloy produced by mechanical alloying was investigated using X-ray diffraction (XRD) and differential scanning calorimetry (DSC) techniques. The measured XRD patterns showed that Se atoms located at interfacial component migrated with aging giving raise to a crystalline selenium (c-Se) phase. DSC spectra of heat-treated samples at temperatures abov...

متن کامل

The Influence Of Process Control Agent (P.C.A)’S State on Expedition of Mechanical Alloying of Anostructure Tial(Γ) Alloy

In this research, the effect of two process control agent: methanol (liquid state) and stearicacid (solid state) on mechanical alloying process of Ti and Al with equal at%(Ti50Al50) wereinvestigated. Phase transformation at presence of two PCA was: at first, powder mixture wastransformed to a metastable solid solution of Al in Ti lattice (disordered hcp) and then transformed toamorphous phase w...

متن کامل

Mechanical alloying of Cu and Fe induced by severe plastic deformation of a Cu-Fe composite

A filamentary composite elaborated by cold drawing was processed by High Pressure Torsion (HPT). The nanostructure resulting from this severe plastic deformation (SPD) was investigated thanks to scanning electron microscopy, transmission electron microscopy, X-ray diffraction and 3D atom probe. Although the mutual solubility of Cu and Fe is extremely low at room temperature in equilibrium condi...

متن کامل

the effects of error correction methods on pronunciation accuracy

هدف از انجام این تحقیق مشخص کردن موثرترین متد اصلاح خطا بر روی دقت آهنگ و تاکید تلفظ کلمه در زبان انگلیسی بود. این تحقیق با پیاده کردن چهار متد ارائه اصلاح خطا در چهار گروه، سه گروه آزمایشی و یک گروه تحت کنترل، انجام شد که گروه های فوق الذکر شامل دانشجویان سطح بالای متوسط کتاب اول passages بودند. گروه اول شامل 15، دوم 14، سوم 15 و آخرین 16 دانشجو بودند. دوره مربوطه به مدت 10 هفته ادامه یافت و د...

15 صفحه اول

Characterization of the metastable Cu-Fe nanoparticles prepared by the mechanical alloying route

Although Cu and Fe are immiscible under equilibrium conditions, they can form supersaturated solid solutions by mechanical alloying. In this paper, nano-structured of the metastable Cu-Fe phase containing 10, 15, 20 and 25% wt Fe were synthesized by intensive ball milling for 15h, in order to achieve a solid solution of Fe in Cu. The phase composition, dissolution of the Fe atoms into the Cu ma...

متن کامل

the effects of planning on accuracy and complexity of iranian efl students’ written narrative task performance

this study compared the different effects of form-focused guided planning vs. meaning-focused guided planning on iranian pre-intermediate students’ task performance. the study lasted for three weeks and concentrated on eight english structures. forty five pre-intermediate iranian students were randomly assigned to three groups of guided planning focus-on-form group (gpfg), guided planning focus...

15 صفحه اول

منابع من

با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

ذخیره در منابع من قبلا به منابع من ذحیره شده

{@ msg_add @}


عنوان ژورنال

دوره 49  شماره 1

صفحات  17- 21

تاریخ انتشار 2016-06-01

با دنبال کردن یک ژورنال هنگامی که شماره جدید این ژورنال منتشر می شود به شما از طریق ایمیل اطلاع داده می شود.

میزبانی شده توسط پلتفرم ابری doprax.com

copyright © 2015-2023