ULTRA FINE FERRITE FORMATION IN Si-Mn TRIP STEELS
نویسندگان
چکیده مقاله:
Abstract: In the present investigation, the effects of thermomechanical processing parameters and the steel chemical composition on the ultra fine ferrite formation characteristics were studied. This was programmed relying on the capabilities of strain induced transformation (SIT) phenomenon and applying to different grades of Si-Mn TRIP (Transformation Induced Plasticity) steels. Accordingly, wedge shaped specimens were rolled at two different temperatures, above and below the austenite-to-ferrite transformation temperature (Ar3). An ultra fine ferrite grain size, in the scale of some hundred nanometers, was obtained by rolling the specimens with lower Si content at a temperature below the related Ar3 temperature. The amount of reduction, which was resulted in the latter microstructure, was realized to be about 55%.
منابع مشابه
THE EFFECT OF STRAINING BEFORE AND DURING AUSTENITE TO FERRITE TRANSFORMATION ON THE FINAL CHARACTERISTICS OF SI-MN TRIP STEELS
TRIP (TRansformation- lnduced- Plasticity) behavior is a powerful mechanism to improve mechanical properties. The basis of TRIP phenomena is the transformation of retained austenite with optimum characteristics (volume fraction, stability, size and morphology) to martensite during deformation at room temperature. Accordingly, the first requirement to obtain desired TRIP effects is to produce an...
متن کاملUltra-Fine Grained Dual-Phase Steels
This paper provides an overview on obtaining low-carbon ultra-fine grained dual-phase steels through rapid intercritical annealing of cold-rolled sheet as improved materials for automotive applications. A laboratory processing route was designed that involves cold-rolling of a tempered martensite structure followed by a second tempering step to produce a fine grained aggregate of ferrite and ca...
متن کاملExperimental Characterisation of the Bainitic Transformation Kinetics of Residual Austenite in Mn-Si TRIP-Assisted Multiphase Steels
Recent studies on TRIP-assisted multiphase steels have emphasised the drastic importance of the bainitic transformation in the optimisation of properties. Bainitic ageing is necessary for the stabilisation of austenite with respect to the martensitic transformation. This metastable retained austenite can still transform to martensite when plastically deformed (TRIP effect). The present work dea...
متن کاملultra-fine grained dual-phase steels
this paper provides an overview on obtaining low-carbon ultra-fine grained dual-phase steels through rapid intercritical annealing of cold-rolled sheet as improved materials for automotive applications. a laboratory processing route was designed that involves cold-rolling of a tempered martensite structure followed by a second tempering step to produce a fine grained aggregate of ferrite and ca...
متن کاملeffect of ai on the hot deformation of ferrite in cu-mn steels.
effect of small al additions, from 0.14% to 0.31% ai, on the hot deformation behavior of low carbon steels containing 1%cu-1.2%mn was investigated in the temperature range of 750-800•c over the strain rate range of 1o.3.1o.1s•1 by a hot compression testing machine. the flow curves obtained, exhibited typical characteristics of dynamic recovery type of softening mechanism, and the critical strai...
متن کاملمنابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ذخیره در منابع من قبلا به منابع من ذحیره شده{@ msg_add @}
عنوان ژورنال
دوره 5 شماره 1
صفحات 1- 7
تاریخ انتشار 2008-03
با دنبال کردن یک ژورنال هنگامی که شماره جدید این ژورنال منتشر می شود به شما از طریق ایمیل اطلاع داده می شود.
میزبانی شده توسط پلتفرم ابری doprax.com
copyright © 2015-2023